Warrego Metal Works

Warrego Metal Works Manufacturer of Ute trays, rigid body stock crates/trays but also specialising in general fab/welding

Custom made shorty 2 box set up FOR SALE. Suit 2100mm wide trays but see below.Passenger side is set up with 2x draws on...
08/09/2026

Custom made shorty 2 box set up FOR SALE. Suit 2100mm wide trays but see below.

Passenger side is set up with 2x draws on slides, driver side is just open
Fabricated on 50mm high x 25 rhs frame
Sheeted centre section with bolt on roof
Set up for a large width tray but I will offer cutting width down to suit other tray widths within price.
510mm wide external
See photos for all other dimensions
Has tray posts welded on to flush finish with tray sides.
Will throw in these tray sides (250mm High x 1465mm L) or can fabricate custom sides to suit with a POA

Completed $5,390 plus GST sand blasted powder coated simple colours. Currently raw but will end up powdercoating white in our next run if not sold.

Tri axle trailer is progressing🤠
31/08/2026

Tri axle trailer is progressing🤠

15/07/2026

130m of welding completed one day last week by Matt and apprentice Alex on a set of fabricated chassis rails for the new build semi 🧑‍🏭👨‍🏭

Fully welded rails front to back, top to bottom

Simple little 20ft ish steel side crate and tray for this single drive acco2mm pressed sides fully welded for longevityS...
13/07/2026

Simple little 20ft ish steel side crate and tray for this single drive acco
2mm pressed sides fully welded for longevity
Side load built into 1300mm pallet door
Aluminium slide out ramp
5mm floor plate
Oversize rear sliding gate with full opening rear door
Rolling centre divide with 50/50 slam shut gates
Stack rod floor grating hinged

New build 45ft Tri-axle lead coming alongFull chassis'd trailer with 20ft of crate and 25ft living
09/07/2026

New build 45ft Tri-axle lead coming along

Full chassis'd trailer with 20ft of crate and 25ft living

Warrego Metal Works recently supplied 6 x adjustable tube dolleys to hold xray tubes for gas pipe weld inspections.
07/07/2026

Warrego Metal Works recently supplied 6 x adjustable tube dolleys to hold xray tubes for gas pipe weld inspections.

Some fabricated pipe and plate assemblies. Hot dipped gal finish
01/07/2026

Some fabricated pipe and plate assemblies. Hot dipped gal finish

Fabricated a grain top for this new little isuzu tipper. Set up for small scale feedlotting.
23/06/2026

Fabricated a grain top for this new little isuzu tipper. Set up for small scale feedlotting.

Quad Cab Ram matched with our 2350mm long tray.Completed with rear 1200mm trundle draw, under tray boxes and a through f...
18/06/2026

Quad Cab Ram matched with our 2350mm long tray.

Completed with rear 1200mm trundle draw, under tray boxes and a through floor second battery mount.

Reverse sensor and camera all cleanly relocated

WMW cruiser tray completed in recent months.Our standard design with a few complimenting features-Rear box tapered draws...
17/06/2026

WMW cruiser tray completed in recent months.
Our standard design with a few complimenting features
-Rear box tapered draws
-Mesh accents
-Jack off skid
-Lightbar and thermal camera headboard mounts
-Headboard enclosure for battery and electrical

We also completed a major rebuild on the aluminium side steps and a touch in the bullbar after these were purchased off a rolled and wrecked it

Address

32 Linton Street
Roma, QLD
4455

Opening Hours

Monday 6am - 5pm
Tuesday 6am - 5pm
Wednesday 6am - 5pm
Thursday 6am - 5pm

Telephone

0408536392

Website

Alerts

Be the first to know and let us send you an email when Warrego Metal Works posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category