Jt Manufacturing LLC

Jt Manufacturing LLC Jt Manufacturing specializes in machining, fabrication, engineering, and product design. We are located in Willis Tx.

We have the capability to make any part or component of any size with a tolerance of 0.0005”.

This 2” diameter hdpe pulley was done in one operation on our cnc lathe. It took me a while to figure out to get the pro...
01/23/2020

This 2” diameter hdpe pulley was done in one operation on our cnc lathe. It took me a while to figure out to get the programming dialed in so it would not break off.

These pictures are from a couple of months ago, but we made a very cool pig in the shop. The biggest diameter was 6” and...
11/22/2019

These pictures are from a couple of months ago, but we made a very cool pig in the shop. The biggest diameter was 6” and the samples was 2”. We removed over 50% of the starting raw material to creat this pig. I was very pleased with how it turned out.
If you need parts made direct message us or send us an email at [email protected]
@ Jt Manufacturing LLC

We reversed engineered some drill press spindles or drill bit holders for one of our customers. These spindles come off...
08/02/2019

We reversed engineered some drill press spindles or drill bit holders for one of our customers. These spindles come off of a 6 head drill press from the 1970’s. The third picture shows the old compared to the new. The new ones are not an exact copy since our customer had us make the end a little long to better hold the drill bit and so that the spindle will last longer. The old design did not leave enough metal between the drill bit hole in the bottom and the thin shaft. The customer was having issue with the spindles because they were breaking. The thin part of the spindle is designed to go into an arm on the machine. It has two spots for bearings and threads for a lock nut on top. The drill bit is held in place in the bottom by four set screws. @ Jt Manufacturing

We made another pig the other day on our manual lathe for one of our customers. Parts like this one, requires a lot of c...
06/26/2019

We made another pig the other day on our manual lathe for one of our customers. Parts like this one, requires a lot of concentration but it’s very gratifying to hold it in your hands once you are done.
If you need parts made direct message us or send us an email at [email protected]


@ Jt Manufacturing

We machined an aluminum pig for cleaning out pipelines the other day. It was a complex, but a fun part to make on our ma...
05/13/2019

We machined an aluminum pig for cleaning out pipelines the other day. It was a complex, but a fun part to make on our manual lathe.
If you need any parts made direct message us or send us an email at [email protected]


@ Jt Manufacturing

A 5” diameter stainless steel part we made the other day. It has a 18 degree internal taper. This part is headed out to ...
04/23/2019

A 5” diameter stainless steel part we made the other day. It has a 18 degree internal taper. This part is headed out to one of the local oil refineries.
If you need parts made direct message us or send us an email at [email protected]

@ Jt Manufacturing

We engineered and designed a reusable impact coating anvil for one of our customers. This little part managed to save ou...
04/04/2019

We engineered and designed a reusable impact coating anvil for one of our customers. This little part managed to save our customer a $1000 a year. The old anvil was a solid piece that had to be replaced after a couple of tests. Our design allowed them to replace the steel ball, which cost a couple of pennies, instead of the entire part. If you need parts made direct message us or send us an email at [email protected]

@ Jt Manufacturing

At Jt Manufacturing we have a lot of services to offer our customers but here are our most common ones. If you need part...
04/01/2019

At Jt Manufacturing we have a lot of services to offer our customers but here are our most common ones. If you need parts made direct message us or send us an email at [email protected]

This was a one off custom shaft that we made for one of our customers. The shaft was first modeled in . Since Fusion360 ...
03/29/2019

This was a one off custom shaft that we made for one of our customers. The shaft was first modeled in . Since Fusion360 drawing environment is so easy to use, we used Fusion360 again to create the drawing for machining on our manual lathe. of worn out parts is hard since you have to use all the knowledge and information you have to make an educated guess at what the dimension of the worn out part should be. With that being said, we nailed it and it was exactly what the customer was wanting. If you need parts made direct message us or send us an email at [email protected]

A box of 3” plastic pulleys ready to ship to our customer. If you need parts made direct message us or send us an email ...
03/26/2019

A box of 3” plastic pulleys ready to ship to our customer. If you need parts made direct message us or send us an email at [email protected]

Address

16170 Cedar
Willis, TX
77378

Opening Hours

Monday 9am - 5pm
Tuesday 8am - 5pm
Wednesday 8am - 5pm
Thursday 8am - 5pm
Friday 9am - 5pm

Telephone

(936) 657-0089

Website

Alerts

Be the first to know and let us send you an email when Jt Manufacturing LLC posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Jt Manufacturing LLC:

Shortcuts

Share

Category