Westport Machine Works

Westport Machine Works Driveshaft, Assembly and Balancing Equipment Manufacturers. Why Does Westport's Equipment Cost Less?

Our products are produced "100%" in our facility in West Sacramento, California. CNC equipment, low overhead and a small family business since 1957, adds up to the highest quality product for the least amount of money. Machining, welding, painting, electrical assembly and quality control all start and finish at Westport Machine Works.

NON-CONTACT SENSOR SYSTEM FOR AUTOMATED OUT-OF-BALANCE DETECTIONThe Shaftmaker G4 is an electronic balancer that uses no...
11/05/2015

NON-CONTACT SENSOR SYSTEM FOR AUTOMATED OUT-OF-BALANCE DETECTION

The Shaftmaker G4 is an electronic balancer that uses non-contact sensors for automated out-of-balance detection. The sensors are permanently mounted and do not require operator adjustment. When the Shaftmaker G4 is in the testing process, the sensors determine the out-of-balance at the head spindle and the tail spindle, displaying the out-of-balance amount of both on the LED touch screen. When the testing process is finished, the machine comes to a stop, then rotates the head end to the top dead center position for weight placement, then the machine will rotate the tail end for weight placement. After the drive shaft is balanced, the operator has the option to print the final results by using the included thermal printer.

Specifications:
• Non-contact sensor system for automated out-of-balance detection
• 17' base
• 12" swing
• 3 HP AC motor
• 0-3000 RPM
• Dynamic breaking
• LED touch screen and thermal printer
• 220 three phase power
• Servo drive
• 15 ton hydraulic system
• 1000 lb. weight capacity
• Machine weight: 3000 lbs.
• 150" spindle face-to-face
• Length 18'6", width 3', height 5'4"

The "POP-IT" hydraulic press is a work center with a vise and a 10 ton hydraulic system. Using the POP-IT in either the ...
09/02/2015

The "POP-IT" hydraulic press is a work center with a vise and a 10 ton hydraulic system. Using the POP-IT in either the horizontal or the vertical position enables the removal and installation of component parts such as, U-joints, center bearings, midship yokes, and slip yokes. Patent . 398,827

Socket Chuck Yoke Fixtures fit the 2-1/4" socket chuck style machines. The Socket Chuck Yoke Fixtures are pre-balanced a...
09/02/2015

Socket Chuck Yoke Fixtures fit the 2-1/4" socket chuck style machines. The Socket Chuck Yoke Fixtures are pre-balanced and come with the strap kit. Socket Chuck Yoke Fixtures are available in sizes from 1210 through 1810 and SPL and RPL. Please call for pricing.

How does the fixturing work?The machine spindles have a female pilot and the fixtures have a male pilot. The fixtures fi...
09/02/2015

How does the fixturing work?
The machine spindles have a female pilot and the fixtures have a male pilot. The fixtures fit into the machine spindles and bolt together with two bolts. The fitting together of the pilot, the face of the fixture and the face of the spindle, creates a sandwich type fit that ensures a long fixture life.

There are yoke fixtures, fl**ge fixtures, and some other fixtures like the ball type fixture. They all bolt to the machine spindles using two hex head bolts or two socket head cap screws depending on the type of fixture. Using these fixtures is how you will hold the customers' driveline in the machine.

PRESS-WELD-STRAIGHTEN-BALANCE ALL IN ONE MACHINESpecifications:• Full length 17' tool tray for operator convenience• 17'...
09/02/2015

PRESS-WELD-STRAIGHTEN-BALANCE ALL IN ONE MACHINE

Specifications:
• Full length 17' tool tray for operator convenience
• 17' base
• 12" swing
• 3 HP AC motor
• 0-3000 RPM digital display
• 15 ton hydraulic system
• 220 Single Phase
• 1000 lb. weight capacity
• Footprint: 204" x 20"
• Weight: 2500 lbs.

NON-CONTACT SENSOR SYSTEM FOR AUTOMATED OUT-OF-BALANCE DETECTIONThe Shaftmaker G3 is an electronic balancer that uses no...
09/02/2015

NON-CONTACT SENSOR SYSTEM FOR AUTOMATED OUT-OF-BALANCE DETECTION

The Shaftmaker G3 is an electronic balancer that uses non-contact sensors for automated out-of-balance detection. The sensors are permanently mounted and do not require operator adjustment. When the Shaftmaker G3 is in the testing process, the sensors determine the out-of-balance at the head spindle and the tail spindle, displaying the out-of-balance amount of both on the LED screen. When the testing process is finished, the machine comes to a stop, then rotates the end with the most runout to the top dead center position for weight placement.

• Non-contact sensor system for automated out-of-balance detection
• 17' base
• 12" swing
• 3 HP AC motor
• 0-3000 RPM
• Dynamic breaking
• 220 three phase power
• Servo drive with HMI control key pad
• 15 ton hydraulic system
• 1000 lb. weight capacity
• Machine weight: 3000 lbs.
• 150" spindle face-to-face
• Length 18'6", width 3', height 5'4"

Address

700 Houston Street
West Sacramento, CA
95691

Opening Hours

Monday 8am - 5pm
Tuesday 8am - 5pm
Wednesday 8am - 5pm
Thursday 8am - 5pm
Friday 8am - 5pm

Website

Alerts

Be the first to know and let us send you an email when Westport Machine Works posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Westport Machine Works:

Shortcuts

Share

Category