Backroads Off-Road & Accessories

Backroads Off-Road & Accessories Car & Truck accessories, tires, LED lights, custom fabrication, welding, lift kits, UTV and ATV accessories

Want to wish everyone a Merry Christmas and a Happy New Year
12/25/2024

Want to wish everyone a Merry Christmas and a Happy New Year

The page was down for awhile and I couldn’t get on it but here is a bunch of project I have done the last couple months.
05/21/2024

The page was down for awhile and I couldn’t get on it but here is a bunch of project I have done the last couple months.

A custom windshield we made for a razor with a aftermarket cage cut the lexan to fit and ordered some Super ATV clamps ...
08/03/2022

A custom windshield we made for a razor with a aftermarket cage cut the lexan to fit and ordered some Super ATV clamps to hold it on.

Someone is getting some new shoes and new painted wheels, hard to believe that yellow came out of a rattle can, it looks...
09/19/2021

Someone is getting some new shoes and new painted wheels, hard to believe that yellow came out of a rattle can, it looks as good as stuff I have painted out of a gun.

Working on a John Deere Gator and it has those new Blue Tooth spark plug wires.
01/17/2021

Working on a John Deere Gator and it has those new Blue Tooth spark plug wires.

We want to wish everyone a Merry Christmas and a Happy New Year
12/25/2020

We want to wish everyone a Merry Christmas and a Happy New Year

Changing all the fluids in a Polaris 4 wheeler over to Amsoil. Think we have a little mud and weeds to go thought to get...
12/12/2020

Changing all the fluids in a Polaris 4 wheeler over to Amsoil. Think we have a little mud and weeds to go thought to get to the plugs.

Been awhile since I have posted anything but haven’t done anything cool and the vehicle I did do I didn’t take pictures....
09/27/2020

Been awhile since I have posted anything but haven’t done anything cool and the vehicle I did do I didn’t take pictures. I am working on a trailer that needed new bearings and the wheel bearings packed and the brakes weren’t working. I noticed the magnets were worn and it just as cheap to put the whole backing plate on. When I was installing the backing plate I seen that the springs weren’t lined up and the center pin was broke, so new pin and u-bolts and it was tracking straight again. Then when the wife says she is tired of hearing the noise in the front of her car you get it fixed. Putting a new set of Monroe struts under it, have to love when they use the strut as part of the knuckle and the upper bearing goes out and starts popping.

Don’t have a clue why the headlights are not working.
06/25/2020

Don’t have a clue why the headlights are not working.

Had a little trailer project I did wired up LED lights on the inside and outside of a enclosed trailer. Put 6 on the out...
06/22/2020

Had a little trailer project I did wired up LED lights on the inside and outside of a enclosed trailer. Put 6 on the out side that are on different switches for each side of the trailer and then a switch for the inside lights. I had to build a box for the switch panel that has a volt meter and a USB port and cigarette lighter plug and below that a master kill switch that shuts everything down. And on the front installed a electric jack to make it easier to jack it up to put it on the truck. It definitely lights up everything around it, the last picture it is in the shop with the shop lights shut off.

Well the 55 got some more done, the ranger seats are mounted, built some custom brackets and had to tack them to the sli...
06/01/2020

Well the 55 got some more done, the ranger seats are mounted, built some custom brackets and had to tack them to the sliders. When they get sent to the seat shop I will finish welding them up so I don’t burn them up. Finished building the exhaust to, built all the tail pipes out from the mufflers over the rear end and around the gas tank ( that was loads of fun not enough hands). Will be leaving to get wiring done so I can get onto other projects.

After the wheel bearings were changed and half the rest of the front end I installed amber and white strobe on the truck...
05/03/2020

After the wheel bearings were changed and half the rest of the front end I installed amber and white strobe on the truck so when he was unloading his track hoe he could make people aware of what was happening. I welded up a bracket for the light bar on the headache rack and installed some LED work lights to.

Address

2218 W Wood Road
Waukomis, OK
73773

Opening Hours

Monday 4pm - 10pm
Tuesday 4pm - 10pm
Wednesday 4pm - 10pm
Thursday 4pm - 10pm
Friday 4pm - 10pm
Saturday 9am - 10pm
Sunday 12pm - 10pm

Telephone

+15805483090

Website

Alerts

Be the first to know and let us send you an email when Backroads Off-Road & Accessories posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Backroads Off-Road & Accessories:

Shortcuts

Share

Category