Schwenke Fab

Schwenke Fab Custom Welding and Fabrication

Built something a little different this time šŸ”„1965 Mustang came in for a full custom exhaust setup—ran 2.5ā€  stainless, ...
05/25/2026

Built something a little different this time šŸ”„

1965 Mustang came in for a full custom exhaust setup—ran 2.5ā€ stainless, built a custom X-pipe from scratch, and finished it off with some Black Widow mufflers.

This one was all about keeping it simple, functional, and sounding right.

Helping  get his EVO dialed in. Updating the downpipe to mate up perfectly with the  titanium exhaust he just picked up—...
05/19/2026

Helping get his EVO dialed in. Updating the downpipe to mate up perfectly with the titanium exhaust he just picked up—clean fitment, proper alignment, and built to last.

Last picture is a shot I took of his car at a roll racing event back in 2018. Watching that car run is what pushed me to buy an EVO in the first place. It’s an honor to work on this car.

Only the best 🤌Super thankful for my amazing suppliers. šŸ’ŖšŸ¼
05/09/2026

Only the best 🤌

Super thankful for my amazing suppliers. šŸ’ŖšŸ¼

Couldn’t sleep, so I came into the shop at 2:30am and jammed out this 10.5 gallon supercharger coolant tank šŸ’ŖSimple, cle...
04/25/2026

Couldn’t sleep, so I came into the shop at 2:30am and jammed out this 10.5 gallon supercharger coolant tank šŸ’Ŗ

Simple, clean, and gets the job done.

Sometimes it’s the little upgrades that make the biggest difference.Picked up a  FlexLoc air-cooled torch for the Multim...
04/16/2026

Sometimes it’s the little upgrades that make the biggest difference.

Picked up a FlexLoc air-cooled torch for the Multimatic 220 setup on the other side of the shop—mainly for tacking parts in tight spots on cars. The adjustability on this thing is a game changer when you’re wedged into places you were never meant to weld in.

Topped it off with a cup because… well, if you know, you know. Clean gas coverage and better visibility makes life a whole lot easier when you’re just trying to get in, tack it, and move on.

Simple setup, but it gets the job done right.

Customer decided to switch it up, so back to the drawing board on this burnout truck’s headers. Second iteration is dial...
04/05/2026

Customer decided to switch it up, so back to the drawing board on this burnout truck’s headers. Second iteration is dialed in—better routing, cleaner fit, no complaints.

You know you made it when you’ve got two die grinders sitting on the bench… just so you don’t have to keep swapping atta...
03/31/2026

You know you made it when you’ve got two die grinders sitting on the bench… just so you don’t have to keep swapping attachments back and forth šŸ˜…

Had to throw the straight die grinder in there too for effect. šŸ˜‚

Efficiency > everything.

03/25/2026
Made quite the investment, and it’s already paying dividends…Picked up a Furick Markout Pro fixture and it’s been a game...
03/25/2026

Made quite the investment, and it’s already paying dividends…

Picked up a Furick Markout Pro fixture and it’s been a game changer in the shop. Layout time is faster, repeatability is on point, and it just makes everything more efficient from start to finish.

Tools that actually improve workflow aren’t an expense—they’re an investment. This one’s already earning its keep.

Address

Dixie Highway
Waterford Township, MI
48329

Alerts

Be the first to know and let us send you an email when Schwenke Fab posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Share