Detroit Muscle Technologies, LLC

Home
Detroit Muscle Technologies, LLC

Manufacturer of the most correct shape and accurate material body restoration gaskets for all muscle

We specialize in Mopar restoration body gasket sets, heater box restoration sets, firewall insulation, etc.

11/04/2026

6003257 E BODY ANTI RATTLE (ANTI BLOW OUT) CLIPS
Factory called these "anti blow out" clips. There are super accurate reproductions with the correct black, hard nylon coating. The only ones being sold with the coating.

06/04/2026

TRK7280AP90 72-80 DODGE TRUCK ACCELERATOR PAD STAINLESS MOUNTING HARDWARE
New, all stainless mounting studs, support plates and bolt. These are usually rusted to the floor.

06/04/2026

ABS (PLASTIC) E BODY PACKAGE TRAYS
Challenger & Barracuda plain, speaker cutouts or speaker and defrost cutouts. Maide from 1/8" ABS with"haircell" texture on one side and smooth on the other. Since these are symetrical the smooth side can be painted with SEM Landau Black automotive interior paint to look factory.

06/04/2026

3441481 B BODY 71-74 NON AC HEATER BOX BLOWER TUBE
Made exactly like OEM from modern EPDM rubber. Has correct shaped "fish mouth" where it attaches to blower motor. Also has a correct "kick" in the long length, again like OEM. The previous reproduction on the market didnt have these.

29/03/2026

62-76 STAINLESS FRONT SHOCK MOUNTS
Reproduction of the front shock upper mounts. I made these for my own 71 Challenger because I'm so tired of anything becoming surface rusty after just a couple years. These are spectacular, heavy weight, stainless reproductions of all hardware. The rubber pieces are firm EPDM rubber exactly like OEM.
Factory part numbers: 2206925 washers, 2206923 grommet, 2298933 1 grommet & 2 washers

29/03/2026

2936926 AC HEATER BOX DRAIN TUBE
This part used to be widely available from left over 50yo inventory but that inventory has now dried up. The few that remain are usually crumpled up from being at the bottom of a box for all those years. No clip. And $50 on Ebay.
I had these reproduced from modern EPDM rubber (same stuff used on door weatherstrip). Also had the internal tooth locking ring reproduced in stainless.
One of these are used on 70-74 E body and 71-74 B body AC heater boxes. Also, TWO of these are used on 72-80 Dodge truck AC heater boxes.

29/03/2026

70-74 CHALLENGER PARKING LIGHT FASTENER SETS
Correct fastenters to install parking lights. The fasteners in the reproduction parking lights being sold are a MILE long. The ones in this set are the correct length. The stamped nuts and black Phillips screws are correct to attach the top of the lamp "arm" to the valance. The oval head, 10-24 screws are correct to attach the bottom of the lamp to the valance. Again, the reproduction lights, that are spectacular, are tapped incorrectly and supplied with TINY 8-32 screws. WTH?!?! I fix that in the parking lamp sets I sell and supply with this fastener set.
PS Everything is stainless except for the stamped nuts (for now).

29/03/2026

71-74 CHALLENGER REAR SPLASH PAN FASTENER SET
FINALLY, a correct set. Needed this for my own 71 Challenger and what was available was just not correct. My car isnt a Hemi Challenger convertible but I wanted accurate fasteners like the factory used. Has the correct fasteners reproduced and correctly coated in black zinc phosphate. A local company here in the Motor City does an incredible job plating the fasteners.
Again the parts are laid out how they are to be installed.
Also have for 70 Challenger since the 70 Challenger rear splash pan is quite different. Will also be doing the 70-74 Barracuda set also.

28/03/2026

STEERING COLUMN INSTALLATION HARDWARE SETS
For all A, B & E Bodies
Steering column gasket, correct ground wire with accurate, reproduction ends (not Radio Shack Sta-Kon connectors), correct reproduction fasteners with correct black zinc phosphate and oil coating. The pictures on the listings show the layout of where all the parts are used. Even how and where the ground strap is installed.
We have (9) versions;
A 67-72, A 73-74, A 75-76
B 66-67, B 68-70, B 71-72, B73-74
E 70-71, E 72-74

28/03/2026

CHALLENGER HOOD SCOOP TO HOOD SCREW SET
Accurate, stainless, reproducton of the correct screws instead of incorrect hardware store pieces. Has the correct thick washer and "type F" thread cutting tip.

27/04/2024

New TA AAR Winshield Washer Squiter Nozzles. Brass body, stainless tubes, zinc plated steel nuts, black e-coated.

Address

23624 Roseberry Avenue
MI
48089

Opening Hours

Monday	09:00 - 17:00
Tuesday	09:00 - 17:00
Wednesday	09:00 - 17:00
Thursday	09:00 - 17:00
Friday	09:00 - 17:00

Telephone

+15867777167

Website

http://www.detroitmuscletechnologies.com/

Alerts

Be the first to know and let us send you an email when Detroit Muscle Technologies, LLC posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Detroit Muscle Technologies, LLC:

Shortcuts

Address
Telephone
Opening Hours
Alerts
Contact The Business
Claim ownership or report listing

Want your business to be the top-listed Equipment Service?

Country:

City:

11/04/2026

06/04/2026

06/04/2026

06/04/2026

29/03/2026

29/03/2026

29/03/2026

29/03/2026

28/03/2026

28/03/2026

27/04/2024

Address

Opening Hours

Telephone

Website

Alerts

Contact The Business

Shortcuts

Share