Overkill Customs

Overkill Customs 3D Printing services specializing in RC along with Offroad apparel We are located in Tavares Florida and specialize in Jeep and 4x4 vehicles.

We are here to offer fully custom fabrication options as well as other modifications to your vehicle. some of our services include:

-Custom bumpers, rock sliders/running boards
-Suspension links and install
-Axle truss installation
-Custom dash/interior
-Trailer modifications/repairs
-Bolt on/weld on suspension kits
-Coilover setup and install (shock tuning outsourced)
-Install of basic bolt on p

arts (body armor, fenders, sliders, etc.) We are also open to any custom fabrication jobs that are not 4x4 related. Shop rates vary by the job and material costs are sperate.

Another one done. Fifth wheel install on a Superduty. From bolt on parts to full builds, we can do it!
03/15/2022

Another one done. Fifth wheel install on a Superduty. From bolt on parts to full builds, we can do it!

Quick turn around job on this super clean FJ. The brand new tires were making contact with the front body mounts so we d...
03/11/2022

Quick turn around job on this super clean FJ. The brand new tires were making contact with the front body mounts so we did a little trimming. The corner of the body mounts were cut of and then capped off. If you need any work done in central Florida give us a message or call for a quote!

Need a custom bracket made or an old one replaced? Message or email us for a quote! This is a replacement bracket in a V...
03/01/2022

Need a custom bracket made or an old one replaced? Message or email us for a quote! This is a replacement bracket in a VW. Now to polish it up and send it out!

Custom low profile 1st gen Dodge bumper. All 1/4” plate with braces and gussets, light bar cutout, and contoured to the ...
02/18/2022

Custom low profile 1st gen Dodge bumper. All 1/4” plate with braces and gussets, light bar cutout, and contoured to the fender wells. High gloss power coated.

Getting work done! This Hummer had old rusted out steps so we took them out and made something better! Decided to change...
02/15/2022

Getting work done! This Hummer had old rusted out steps so we took them out and made something better! Decided to change the round tube to 2"x2" square tube to give a cleaner profile on the side of the vehicle. Now all they need is some paint! I there's any work you need done give us a call/message and we can get you on the schedule! be sure to share our page with all your Jeep and 4x4 friends!

02/12/2022

JK looking all fancy with this ARTEC Industries truss and LCA skids getting burned in!

All sorts of ARTEC Industries goodies going on this JK44. Apex truss and LCA skids should add enough beef to this axle t...
02/10/2022

All sorts of ARTEC Industries goodies going on this JK44. Apex truss and LCA skids should add enough beef to this axle to ensure it can handle all the rocks!

More aluminum work. 3/16" aluminum door armor for these TJ half doors. These have held up to a beating the past year! Ev...
02/09/2022

More aluminum work. 3/16" aluminum door armor for these TJ half doors. These have held up to a beating the past year! Even after this Jeep laying on its side on this armor they protected the factory door from damage in a flop on Carnage Canyon CO. If I started to do small orders on custom parts to pickup or ship out who would have an interest?

Rear deck kit on a Jeep TJ. All framed out with 3/4” tube and covered with 3/16” aluminum. All the hardware was counters...
02/07/2022

Rear deck kit on a Jeep TJ. All framed out with 3/4” tube and covered with 3/16” aluminum. All the hardware was countersunk to sit flush and simple button style hood latches keep it clean and simple. And of course we used our preferred coating of choice Steel-it Stainless Steel Coatings to protect everything! Call us for a quote on whatever you need!

Custom bumpers! This 2000 4Runner got a front and rear bumper kit from Costal Off-road and needed them put together. We ...
02/04/2022

Custom bumpers! This 2000 4Runner got a front and rear bumper kit from Costal Off-road and needed them put together. We assembled them piece by piece, welded, and finished them. Weather it’s a kit or a completely custom design from scratch it can be done here!

Added a steering stabilizer to this 79 Dodge. Started with some hefty tabs welded on to the Yukon Gear & Axle cover on o...
02/03/2022

Added a steering stabilizer to this 79 Dodge. Started with some hefty tabs welded on to the Yukon Gear & Axle cover on one end and a beefy PSC 1.5" clamp on the other to hold up a new FOX 2.0 stabilizer. Cast iron cover was cleaned well and preheated to 400° before burning in the tabs followed by post heating ensure slow cooling and a proper bond between the two metals.

Address

Tavares, FL
36330

Website

Alerts

Be the first to know and let us send you an email when Overkill Customs posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Overkill Customs:

Shortcuts

Share