Dugas Auto & Metal Fab LLC

Dugas Auto & Metal Fab LLC Durham Maine, automotive repair & metal fabrication

🚗❄️ It’s been a while since we’ve posted, but rest assured—we’re still hard at it! Now’s the perfect time to get your ca...
09/12/2025

🚗❄️ It’s been a while since we’ve posted, but rest assured—we’re still hard at it! Now’s the perfect time to get your car serviced and ready for winter. Give us a call today to schedule!

🔧 Here’s a sneak peek at one of our current restoration projects… let’s just say it’s getting a little extra power. 💪 Stay tuned—more to come!

Another one saved. 2012 F250.
11/27/2024

Another one saved. 2012 F250.

HERE IT IS FOLKS! We finished the jeep build and she’s off to her owner!
10/13/2024

HERE IT IS FOLKS! We finished the jeep build and she’s off to her owner!

Well this ole girl has come to us a few times to be straightened out and brought back to life. This is a 97 OBS F350 wit...
10/13/2024

Well this ole girl has come to us a few times to be straightened out and brought back to life. This is a 97 OBS F350 with a power stroke. This time around we lifted and supported the cab removed all the interior. Cut the floor pan on the driver side out and replaced it. We then welded in a new cab mount (cab side) for the body mount to sit on along with a floor pan support from underneath. We also removed the rear cab support crossmember which had failed. We cut the rot out and welded in new steel for the body mounts to sit and re-installed. For the final touches we seam sealed all the panels replaced, epoxy primed, paint, added 80mil sound deadening material to the cab floor a new carpet with pad and a new used seat.

Quick sneak peak…… We’re building a jeep from the ground up! Stay tuned 🤙🏻 Lots & lots of working going into rig!!!
03/02/2024

Quick sneak peak…… We’re building a jeep from the ground up! Stay tuned 🤙🏻 Lots & lots of working going into rig!!!

We know it’s been a hot minute since we’ve posted anything. However we’ve been crazy busy and we’re still helping custom...
02/10/2024

We know it’s been a hot minute since we’ve posted anything. However we’ve been crazy busy and we’re still helping customers to keep their vehicles on the road. Here’s a 2007 GMC 2500 we welded in cross members, a couple frame patches, descaled the frame, sealed it & painted it. Afterwards we rebuilt the front bump stop brackets, installed Timbrens & installed a 8.6’ SS Vplow. To top it off we then sprayed the entire undercarriage with Fluid film to help prevent corrosion from harsh chemicals that are applied to our roads during the winter months.

THIS Will BE THE LAST BIT OF BODY WORK WE DO. Metal fabrication is something we do but we are going to stop doing body w...
08/25/2023

THIS Will BE THE LAST BIT OF BODY WORK WE DO. Metal fabrication is something we do but we are going to stop doing body work as of today. Here’s a quick patch job we did to an older lexus along with some spot blasting and some fluid film. The repairs were done to eliminate the rust that had taken over the rear lower quarters. The welds were cleaned and treated then seam sealed. Customer was very happy and headed right home to throw his rear bumper cover back on.

Here’s another one we finished up. Upgraded, steering, wheel bearings, front axle U-joints, complete vehicle brake job, ...
07/13/2023

Here’s another one we finished up. Upgraded, steering, wheel bearings, front axle U-joints, complete vehicle brake job, drain fuel clean out tank & lines, New fuel tank skid and straps & re-geared axles from 3.07’s to 4.10’s & a new battery. We also took apart the aftermarket control arm bushings & cleaned them out so they’d move freely. This jeep was very meticulously maintained but it had some severe rot in the frame where they all seem to rust. It had been repaired a few times prior and finally let go. We sand blasted the frame & undercarriage, plasma cut out all the rust, welded in new frame safety caps, upper coil buckets and axle side coil buckets. We then sent her in for a full 4wheel alignment. This 24 y/o rig lives on again!!!!

Giving vehicles another shot at life is expensive but cheaper then replacing. What we did here. Water blasted the heavy ...
06/20/2023

Giving vehicles another shot at life is expensive but cheaper then replacing. What we did here. Water blasted the heavy rust areas, cut out the rot and repaired the frame. We then descaled the rest, replaced a cross member, new rear shocks, differential flush and refill along with a new cover and gasket ,new fuel lines, ac belt and tensioner. The frame was sealed and fluid filmed. We then had to repair the bed as 90% of the bed bolts snapped off. We also located a southern rust free bumper and tailgate.

Quick wheel refinish job. The wheels where sandblasted and painted. Then we mounted & balanced a new set of michelins to...
04/30/2023

Quick wheel refinish job. The wheels where sandblasted and painted. Then we mounted & balanced a new set of michelins to make it a complete package

Took Last Week Off To Do Some Major Cleaning & Haul all Of our Junk To The Scrap yard!!!
04/24/2023

Took Last Week Off To Do Some Major Cleaning & Haul all Of our Junk To The Scrap yard!!!

Address

South Durham, ME
04222

Opening Hours

Monday 8:30am - 4pm
Tuesday 8:30am - 4pm
Wednesday 8:30am - 4pm
Thursday 8:30am - 4pm
Friday 8:30am - 4pm

Telephone

+12079392173

Website

Alerts

Be the first to know and let us send you an email when Dugas Auto & Metal Fab LLC posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category