What are the opening hours?

Monday 9am - 5pm Tuesday 9am - 5pm Wednesday 9am - 5pm Thursday 9am - 5pm Friday 9am - 5pm

Shop-Force

Shop-Force provides high-quality machine tool accessories for professional machine shops, manufacturers, and machinists.

From ER collets and collet chucks to end mill holders, live centers, drill chucks, toggle clamps, and more, we deliver dependable tool

10/28/2026

Swap the insert. Change the speed. If the point your part spins on isn't holding its tolerance, the finish was decided before the first cut. The live center is the one piece of the setup almost nobody inspects - and the one that sets the runout ceiling for the whole cut. The 3MT Super Precision Live Center holds +/- 0.0004 T.I.R. with a one-piece forged alloy steel body and spindle and a triple-bearing design for rigidity under load. Check the tailstock point. Shop'sChoice.

10/26/2026

Most toolrooms buy a drill chuck arbor on price, then wonder where the runout came from. On a partially ground 1/2 in to JT2 arbor, only the surface the chuck actually grips is ground. That surface sets the hole, and that is where taper-to-shank runout gets read: under 0.001 in T.I.R. Ground alloy steel 42CrMo, hardened to roughly 52-58 HRC, holds the fit past the tenth setup. Grinding the whole shank adds cost, not accuracy, if the chuck never touches it.

10/25/2026

Every toolroom has a number: the runout you'll tolerate on a keyless chuck before it goes back on the shelf. Some of you want half a thou. Some never put an indicator on it at all.

Our 1/64"-3/4" 3-Jacobs taper keyless chuck runs under 0.003"-0.006" T.I.R. and holds G6.3 balance to 10,000 RPM - nickel-coated, hardened, precision ground.

So where's your line? Drop the number you actually live with.

10/23/2026

The tang on your drill chuck arbor isn't what drives the drill. The Morse taper's friction does. Seat it clean and dry, set it firmly, and the taper locks itself in. The tang only keeps the arbor from spinning loose, and gives you a lip to knock it out with a drift. So when a chuck slips, don't blame a weak tang - check the taper for burrs, oil, or a poor seat before you swap anything. MT2 to JT3 drill chuck arbors, Shop'sChoice.

10/21/2026

Your live center is the point the part actually spins on - so why is it the one taper nobody dials in? The chuck gets an indicator check every job. The cone you set once and forget drives the same roundness you chase at the head. Our 3MT super precision live center holds +/- 0.0004" T.I.R. with a triple-bearing forged body rated to 450 lb max load. Dial the tailstock before you blame the insert.

10/21/2026

The size on an ER collet is a range, not a target. A 1/2" collet holds more than 1/2" - it collapses across a working span, and the grip lives inside that span. Size the tool to the middle and it seats full-length in the bore. Push to the edge and the contact patch shrinks, the tool walks, and the collet takes the blame for a setup that was never inside its range. Our 12-piece ER32 ULTRA set covers 1/8"-13/16" in 1/16" steps, held to 0.0001"-0.0002" T.I.R. Match the range, then the number.

10/19/2026

If only the far end of your shaft reads out of round, the tool, the insert, and the machine get blamed before the tailstock does. A tired live center lets the work deflect outboard, so the finish drifts away from the chuck.

The 3MT Super Precision Live Center holds +/- 0.0004" T.I.R. and 450 lb max load. Check the center first. Shop'sChoice live centers.

10/18/2026

Torque shouldn't change with who's holding the wrench.
Torque an ER collet nut by feel and the number moves with whoever's at the bench - and runout moves with it. A CAT/BT 40 tightening fixture squares the holder before you lean on the nut, so the seat repeats shift to shift.
Heat-treated HRC 30-40 body, ground finish. Vertical or horizontal, off the machine before it ever touches the spindle.
Shop'sChoice CNC tightening fixtures

10/16/2026

The flat tang on an MT2 to JT3 arbor isn't what holds your drill chuck. It has three jobs, and gripping isn't one of them: it seats the arbor in the spindle slot, it ejects the arbor when you back the quill out, and it resists spin under load.

Holding force comes from the Morse taper itself - clean, dry, and seated hard. If a chuck walks, check the taper fit and the seating before you blame the arbor. Match the arbor to your spindle and it stays put.

10/14/2026

Load a collet the wrong way and you can see the accuracy leave before the spindle ever turns. Thread the nut onto the chuck first, then push the collet in, and the nut's eccentric ring has to flex to line up - and that bend shows up later as runout you can't dial out. The fix takes two seconds: snap the collet into the nut until it seats square, then set the pair into the chuck. Same collet. Same chuck. The T.I.R. you paid for.

Address

31525 Aurora Road , Unit 1B
Solon, OH
44139

Opening Hours

Monday	9am - 5pm
Tuesday	9am - 5pm
Wednesday	9am - 5pm
Thursday	9am - 5pm
Friday	9am - 5pm

Website

http://shop-force.com/

Alerts

Be the first to know and let us send you an email when Shop-Force posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.