Morath onsite welding & repair LLC.

05/23/2026

Mini buckets that are taking a lot of abuse.
Hard face✔️
teeth ✔️
Wear bars✔️

We have 6 to do. We weld the teeth on due to an issue with the retention pins coming loose. Common issue. So per customer request, we weld them.

05/23/2026

We built a gate. Set post in concrete, set gate, and added a brace cord. Nothing special. We also had to take a tree out. It all worked out.
I’m not an arborist, never claimed to be. It would be kinda crazy to call some one for such a quick tree job so we tackled it ourselves. Super thick timber so it wouldn’t exactly fall over without getting caught upright.

05/22/2026

This is definitely over kill for a chevy small block !!!! This customer knew exactly what he wanted, we just built it. This engine stand we built is for semi engine. Customer had the idea to mount an irrigation gear box to turn the motor to orient the motor for easy access.
This thing is heavy but should work great for rebuilding motors. Definitely a massive engine stand !!!!

05/17/2026

We extend our gratitude to the Galesburg FFA Alumni and Supporters for inviting us to their Ag Day. We consistently anticipate participating in this event to support the next generation of young men and women involved in agriculture.
We discussed welding and other services we provide, including rope access welding, which entails suspended millwright and weld repair in inaccessible areas.
This requires accessing these areas using ropes. We also emphasized our commitment to safety when utilizing these tools. It's a valuable opportunity for the local agricultural community.

05/17/2026

05/16/2026

Had to go and take a weld test to re certify. These are what a cert test looks like. It shows the weld inspector you can set up a joint correctly, set your machine to the proper parameters, and execute proper technique while Welding. one weld test is a vertical up. The other weld test is overhead.
There is no ABCs or D’s. either you pass or you don’t. I’m going to celebrate by working this weekend 😂🤘🏻

05/11/2026

These guys do great work !!!

04/30/2026

When we are in a pinch and have to move something stubborn, we definitely have the tools to do it…. We have a full set of tnt hydraulics just for rainy days. We use them way more than I would have anticipated. This ram alone will extend to 50” making it light work for lifting and bending things that won’t move.
As for pushing force it will lift 51,000lbs. Usually our average rams have 6”-10” of lift range. This definitely makes it nice for big lifts in the field on soft ground.

04/21/2026

This has been in the works for a while but with the busy spring season we held off for a little while before advertising. We replace spindles on semis, semi trailers, all the way down to 2500 trucks !!!!!! On the side of the road or right in your shop !!!! We come to you !!!! This will open up another service to best serve our customers and provide solutions to your problems !! Feel free to share

04/14/2026

Added some agitation to this tanker.

We DO NOT USE SPARGE LINES. We do agitation a very specific way without having to use a ton of expensive stainless pipe $$$. Sparge lines are not as efficient as our system. Our system mixes every thing before it’s pumped out and lifts the product out of the sump more effectively so there no concentrated spots in the mix.
We tie into your existing pump line and put an inline valve. For every gallon that’s pumped through the mixing lines, it mixes 2-3 gallons in the tank. So if you have a 500 gallon per minute pump, it mixes approximately 1000-1250 worth of product in one minute, give or take a few gallons. Let the pump agitate for 2-3 minutes and your tanker is now safe to load sprayers.
This is tanker #7 we’ve done and every customer has been very happy with the results

04/14/2026

Fixing pin holes from bad welds is not my most favorite thing to do… but I do it. We replace pipes. We do not weld over the already 10lbs of weld lol.

More weld does NOT mean better lol