Cramer's Mobile Welding &Fabrication LLC

Cramer's Mobile Welding &Fabrication LLC Mobile welding company, 24/7 emergency repair, Ag repair, fab work, hard facing

We recently built these replacement floor grates for Aubrey Alexander Toyota, due to their old ones breaking
03/14/2026

We recently built these replacement floor grates for Aubrey Alexander Toyota, due to their old ones breaking

We haven't posted in awhile but here is some of our most recent fixes the first on a broken stump grinder the second on ...
10/12/2025

We haven't posted in awhile but here is some of our most recent fixes the first on a broken stump grinder the second on a busted grain drill axle and some pictures of some dumpsters we repaired

Yesterday we helped a customer out by fixing a few broken components on a backhoe
11/03/2024

Yesterday we helped a customer out by fixing a few broken components on a backhoe

Today we worked on this Hesston 4900 for a customer. We went over the entire baler and repair a few cracked welds inside...
09/02/2024

Today we worked on this Hesston 4900 for a customer. We went over the entire baler and repair a few cracked welds inside the bale chamber. Since the baling season is coming to a close if you have any welding repairs that need done to balers, tedders, rakes, mowers, or mergers shoot us a message or give us a call

It's been a very busy couple of days first we welded in a few floor supports underneath a RV, secondly we re-welded some...
08/06/2024

It's been a very busy couple of days first we welded in a few floor supports underneath a RV, secondly we re-welded some cracked welds on a boat trailer hitch, On Saturday and a part of Sunday we replaced a rotted out cross member and plated some of the frame on a chevy 1500 and to finish up today we assembled a custom gear puller to be used on a big square baler for a customer.

A few recent fixes and a fab project
07/10/2024

A few recent fixes and a fab project

Today we worked on a hay wagon that had some broken horizontal supports.
03/29/2024

Today we worked on a hay wagon that had some broken horizontal supports.

Today we did a frame repair on a dodge 1500, we removed the bed and cut out two rusted out crossmembers and replaced the...
02/17/2024

Today we did a frame repair on a dodge 1500, we removed the bed and cut out two rusted out crossmembers and replaced them with c-channel then made 2 patch plates to seal holes that rust started to form on the frame, built a new shock mount, then prepped the frame and painted it and re mounted the bed. We don't do alot of frame work but no job is too much for us give us a call at 570-765-4593 for all of your welding needs.

This past Sunday we traveled to Lewistown PA to repair handrailing on an old and out of code fire escape after some cutt...
02/14/2024

This past Sunday we traveled to Lewistown PA to repair handrailing on an old and out of code fire escape after some cutting welding and alot of grinding we came up with brand new railing that is well within code and will more then likely out live the building. For any repair welding or fabrication give us a call at 570-765-4593

Took a hot humid Saturday trip out to Lewistown for a couple hours to build some handrailing for a customer down to her ...
09/09/2023

Took a hot humid Saturday trip out to Lewistown for a couple hours to build some handrailing for a customer down to her basement some inch and a half square tubing and 4 custom cut mounting pads some welds bolts and paint and that's a wrap

On August 19th we took a trip to Harrisburg to put this decorative piece back into a handrails a few small welds and som...
08/24/2023

On August 19th we took a trip to Harrisburg to put this decorative piece back into a handrails a few small welds and some paint, remember no job to small or big it can be done.

Yesterday we traveled to Lewistown to fix a factory mistake on a grapple bucket. The pin locks were set way to low from ...
08/24/2023

Yesterday we traveled to Lewistown to fix a factory mistake on a grapple bucket. The pin locks were set way to low from factory and when the customer would tip the grapple forward it had enough play to actually fall off the tractor. So we cut those off and made new ones out of 3/8 inch ARr450 for good strength and raised them about a 1/2 inch higher then the factory ones making it tight enough to barely have any play but still easy to lock.

Address

208 Hyonahill Road
Middleburg, PA
17842

Website

Alerts

Be the first to know and let us send you an email when Cramer's Mobile Welding &Fabrication LLC posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Cramer's Mobile Welding &Fabrication LLC:

Shortcuts

Share

Category