Ellis Race Cars

Ellis Race Cars Chassisworks & Fabrication

I can’t say enough good things about Hammer B Hamm .. it turned out badass and can’t wait to see it under the car. Thank...
11/15/2024

I can’t say enough good things about Hammer B Hamm .. it turned out badass and can’t wait to see it under the car. Thank you and your team, sir!

Did some minor updating/changes on 2 cars out of the same race program here at the shop. Jeff James-Big Block Killer nee...
08/06/2024

Did some minor updating/changes on 2 cars out of the same race program here at the shop.

Jeff James-Big Block Killer needed some odds and ends done to his car so he could get it back out and get the new combo tested when work allowed.

She’s on small tires boys!

-We got the front struts changed out to some AFCO Racing terminator’s with canisters. Mounted on some mounts from LJRC.
-Also swapped the rear coilovers from santuffs to AFCO big guns.
-Added a puke tank to the car
-also got his dump valves mounted so they no longer hit the double rail.
-Added shock sensors to keep tabs on what the car is doing from

Jeff also dropped this nice 4th gen off so we could get it put back together for Jason to get back behind the wheel.

-got the SBC put in along with a ProCharger f3r procharger
-got the Holley dominator and components laid out using Leash Electronics equipment and Earth MotorCars and friends helping with some wiring and parts acquiring also.
-built a set of headers for it with a Stainless Works kit
-fit a new front end on the car from Vfn Fiberglass (let’s add a hood option for the legal non factory firewall stuff)
-added shock sensors for data from Lowdoller Motorsports
-went through the car and rerouted a lot of things to make it flow better
-custom fuel cell and puke tank by us
-plumbing and mounting of the fuel system. A lot of it was bought from Alkydigger Fuel Injection, Superchargers, and Ignitions
-added a burst plate to the 417 Motorsports elbow

This fall these 2 will be ready to test. Thanks again guys for letting me be a very small part in helping!

Let’s see if we can math with these
07/18/2024

Let’s see if we can math with these

The mustang went home for a few odds and ends. It’ll be back for wiring, body work and paint later this summer/early fal...
06/20/2024

The mustang went home for a few odds and ends. It’ll be back for wiring, body work and paint later this summer/early fall

It was nice to step aside from race cars during the holiday weekend and get the yard be**er back up and safe. 4 wheel be...
05/28/2024

It was nice to step aside from race cars during the holiday weekend and get the yard be**er back up and safe.

4 wheel bearings, prop shaft, tie rods, front and rear windows and a set of doors I got off a friend.

At least it won’t break down in the yard

When you’re looking for that girl that drinks fine wine in the Arkansas bottoms.
05/21/2024

When you’re looking for that girl that drinks fine wine in the Arkansas bottoms.

Got the helper tightening the Christmas tree brackets while dad builds an exhaust.
04/11/2024

Got the helper tightening the Christmas tree brackets while dad builds an exhaust.

Had to bite the bullet and do a thang. Thanks a lot CJ Race Cars
01/10/2024

Had to bite the bullet and do a thang. Thanks a lot CJ Race Cars

There won’t be any issues stopping this thing
10/31/2023

There won’t be any issues stopping this thing

Address

Marked Tree, AR
72365

Telephone

+18702270418

Website

Alerts

Be the first to know and let us send you an email when Ellis Race Cars posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category