Swamp Green Fabrication & Repair

Swamp Green Fabrication & Repair In shop & on-site wedding and repair. Core drilling & concrete anchoring. Any custom fabrication & metal work. Alignment, layout, and installation. Trailer repair.

Gates, hand rails, and fences. Farm & construction equipment. NO JOB TOO BIG OR TOO SMALL!

Hoist pole for the coolest CB tower/antenna set up I’ve ever seen. This was one of those projects that makes me really a...
06/28/2025

Hoist pole for the coolest CB tower/antenna set up I’ve ever seen.
This was one of those projects that makes me really appreciate getting to meet and work for some really great people.
The tower hinges at the base so you can raise and lower the tower as needed. Obviously with the extreme length and weight of this tower, it’s just about impossible to raise and lower it by hand. So what we did was, get a long stick of 4”x1/4” square tubing, weld a pulley and a couple eye bolts up top as well as a winch plate at the base. We dug a hole, set the base of the pole 4 feet in the ground and filled it with cement. With the leverage point being over 20 feet off the ground this allows for easy and effortless raising and lowering of the CB tower.
You know it was a good job when the only difficult part of the job is material handling!

Seriously overbuilt RV cargo rack. Weighing in at roughly 250 pounds of steel alone, this rack will out live this RV and...
06/28/2025

Seriously overbuilt RV cargo rack. Weighing in at roughly 250 pounds of steel alone, this rack will out live this RV and the one after that, and the one after that! Along with adding some support bracing to the hitch receiver and frame rails of the rv, this project was a good mix of shop and on site fabrication.

Modular design railing. This was a not so standard way to make a very standard design which always makes things interest...
06/28/2025

Modular design railing. This was a not so standard way to make a very standard design which always makes things interesting! The main purpose is obviously a standard railing. The not so standard part was making it modular. 3 sections, with 2 sections being anchored to the concrete and still removable and then one section that slides into 2 stake pockets and tightens down for quick and easy removal and re-install. The purpose for this design is to be able to easily remove a section and place ramps there for moving appliances, furniture, or anything big in and out of the house. We did all the fabrication and paint in the shop and then did the install onsite with the help of the customer. This was a fun project and I got to meet and work with some good people in the process

Feeder mount number 2. Made this weldment to mount to the front of a pickup. Took some 3/8 thick flat bar and welded som...
12/18/2024

Feeder mount number 2. Made this weldment to mount to the front of a pickup. Took some 3/8 thick flat bar and welded some spacer plates on and put a slight bend in it in hopes of matching the curvature of the truck bumper. Then some square tube to gain some height and more flat bar with studs welded in to mate with the bracket on the feeder to make for easy install and removal. Then the bracket on the feeder to give it a strong attachment point.

Quick repair and improvement on this hitch mounted road feeder
12/18/2024

Quick repair and improvement on this hitch mounted road feeder

Quick 2 machine job for a customer. Craftsman push mower that needed some love. We did a basic tune up and blade sharpen...
10/24/2024

Quick 2 machine job for a customer. Craftsman push mower that needed some love. We did a basic tune up and blade sharpen on the mower as well as a crankshaft key, valve job, head gasket and breather gaskets. For the generator we did a tune up, carburetor rebuild and extensive power output testing to make sure this tiny beast was operating at its fullest capabilities. These Honda small engines definitely live up to the hype without a doubt!

Just a couple of shop projects from awhile back. Torch cart and a 3 tier welding cart. Both made 98% from old scrap meta...
10/24/2024

Just a couple of shop projects from awhile back. Torch cart and a 3 tier welding cart. Both made 98% from old scrap metal / bed frames that were about to be tossed (the other 2% is the wheels). And of course we had to paint them swamp green! Version 2 will be coming soon! The plan is to make a more rough terrain version of both of these for mobile welding jobs. Because making abstract equipment like that is a lot more fun than just buying longer leads. After all, there’s no kill like overkill!

First job done and delivered back to the customer. This RZT got a basic tune up as well as some much needed TLC includin...
08/11/2024

First job done and delivered back to the customer. This RZT got a basic tune up as well as some much needed TLC including a deck spindle, new blades, new deck lift cables, ignition, hydro gear adjustment, charging system work, a whole lot of bearing grease, and a much needed wash.

Hey SETX, we are open and ready for business. We specialize in welding projects / fabrication, lawn equipment repair, me...
08/05/2024

Hey SETX, we are open and ready for business. We specialize in welding projects / fabrication, lawn equipment repair, mechanical troubleshooting and repair, and any other residential needs. We are the one stop shop for all your repair needs and we’ll compete with any price in the area. We guarantee top dollar quality with the best prices around.

Address

Lumberton, TX
77657

Website

Alerts

Be the first to know and let us send you an email when Swamp Green Fabrication & Repair posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category