VRN Welding & Fabrication, Inc.

06/05/2026

Happy Friday, everyone!

We recently had the pleasure of helping out one of our good friends, Mr. Fabulous, with his ’86 Monte Carlo!

Alan doesn’t get to race very often because of everything he does for the racers, for us here at VRN, for the racing community, and for Great Lakes Dragaway. With his new A-Team Motorsports Big Block Chevy, we knew the rear of the car needed to be ready to handle the power.

Here at, VRN Welding & Fabrication we made sure it was up to the task!

We upgraded the car with:
New driveshaft
Disc brakes
Center section
Axles
Spool
Coil-over shocks
And much more!

Alan took the car out for the Memorial Day Classics, and it went down the track straight as an arrow! Even better, he laid down personal best after personal best throughout the event.

We're proud to have been a part of this build and can't wait to see him break into the single-digit zone with his street car!

Here are a handful of photos from the project and its first successful outing.

05/14/2026

We could not be happier with how this housing turned out!

Give us a call to get yours on order today!

(847)735-7270

04/17/2026

Don’t forget your driveshaft needs — we’ve got you covered!

Give us a call at the shop at 847-735-7270, and we’ll take care of you.

04/15/2026

🚨 DRAG RACERS 🚨

If you’re putting down real horsepower and actually leaving hard… you already know what happens next — twisted tubes, bent housings, and missed race days.

That ends here.

Our fabricated housings are built for one thing: taking everything you throw at them and asking for more.

🔥 Designed for high HP
🔥 Fully reinforced to eliminate flex and failure
🔥 Built to stay straight under extreme load
🔥 Consistent, predictable performance pass after pass
🔥 Machined face plate to ensure a perfect seal, and to keep everything aligned

You didn’t build your car to go easy — don’t trust it to weak parts.

💥 Leave harder💥 Hook better💥 Stop worrying about breakage

📩 Message us to get your housing built — custom setups available for any combination!

When it’s time to line up… make sure your rear end is ready.🏁💨

*Featured is another one of our floater dragster housings going in a Procharged American race cars chassis. Thank you Coleman Motorsports for choosing us to strengthen your ride!

04/15/2026

04/07/2026

Just a reminder to get your set of these for the season!

04/02/2026

WE NEED YOUR HELP!!!

Motorsports Fans: We need your help to protect our sport! 🏁

We are reaching out as we get closer to the deadline for Wisconsin’s Assembly Bill 880 (The Right to Race Legislation). This bill is vital for protecting our racing facilities from nuisance actions and ensuring the future of motorsports in our state.

Please note that we are stronger together, and in no way are we trying to be rude or brash. We simply ask you to show Governor Evers your overwhelming support by leaving a positive and supportive message. There is no room here for anger, attacks, or unpleasantness in these messages.

HOW YOU CAN HELP:
1️⃣ Call 608-266-1212
2️⃣ Press 1 to leave a message.
3️⃣ Ask: “Governor Evers, are you planning to sign the Right to Race Legislation AB 880?”

Let’s work together to get this bill across the finish line! 🏎️💨

02/09/2026

Don’t forget!

01/27/2026

Resharing :) Get yours asap!

01/05/2026

If you’re updating your car and don’t want to spend extreme amounts, we got you covered with our economy 9 inch housings. Offered with a 3 1/4 inch axle tube built to handle steady power, these housings are much more cost effective for those wanting a clean and neat look in the rear of the car.

Call (847-735-7270) or message us to get yours!