Uncle B's Gunsmithing LLC

Uncle B's Gunsmithing LLC Hi, my name is Brett Michel, founder and owner of Uncle B's Gunsmithing LLC. I've been a local hunter and fisherman since a very young age.

Providing safe, quality care and service to firearms and related equipment.

•Clean/inspect
•Repair
•Refinish/Restoration
•Cerakote
•FFL Transfer/Sales
•Barrel Threading
•Slow Rust Bluing
•Mount Optics & Zeroing
•Fit/Install Recoil Pad I spent 8 years in the United States Marine Corps where I served in the Infantry as a Heavy Machine Gunner 0331. After receiving an Honorable Discharge from the Co

rps, I pursued my education. I graduated and now work part-time as a Registered Nurse in a local ER. I also completed Gunsmith training at Penn Foster where I earned my Career Diploma in Gunsmithing. I’ve also spent many days over the years working alongside other gunsmiths. I am proud to hold the title of "Gunsmith." I have found something I truly enjoy doing. So, if you have gun work...bring it to me. I will treat your firearms as my own and give you honest, helpful advice. My goal is to provide safe, quality care for your firearms and related equipment. Services:

-Sales and Transfers
-Cleaning
-Parts Repair
-Reblue
-Wood Repair/Refinish
-Cerakote (oven and air cure)
-Barrel Threading
-Bolt Knob Enhancements
-Optics Install
-Customization and Upgrades
-Appraisal
-Restorations

Must know SOPs :

-Sales only on "Proceed" from NICS/background check.

-$25 FFL transfer fee

-Upon transfer from customer to Uncle B's Gunsmithing, an observation of previous damages will be recorded on paper diagram and require signature of customer, acknowledging existing damages prior to transfer.

-Cerakote prices can change depending on application type/size/assembly/reassembly/paint choice

06/23/2026

Close enough…

Alright, I had fun on the lathe today with this quick project. I was in need of an extension for a 10mm shanked Forstner...
06/02/2026

Alright, I had fun on the lathe today with this quick project. I was in need of an extension for a 10mm shanked Forstner bit that would accommodate this project. I could not find anything that suited my needs and was priced right…so I made one.

Don’t get me wrong…this was no amazing feet, but it did feel good making it. I used a segment of scrap stainless steel rifle barrel that I cut off from a previous job. I cut to desired dimension, bored, drilled, and tapped the tool head. I installed the bit and secured it with 6 set screws. It’s perfect and cost me only about an hour of my time! And now I have the tool for future needs. Thats a good day!

In the future, I plan to make bushing sets for the tool, as needed. For this project, I only needed to make a few passes to reach my goal. With a sharp bit, slow passes, and a steady hand, the job was finished in seconds.

Stay tuned for the restoration of this Re*****on Model 11 I’ve been working on. Happy hunting!

“It shouldnt be too dirty.”…famous last words 😎 Get em cleaned up and ready! Duck season will be here before you know it...
06/02/2026

“It shouldnt be too dirty.”

…famous last words 😎

Get em cleaned up and ready! Duck season will be here before you know it!

05/15/2026

Just getting some fresh air.

A pair came in for threading. Barrels were cut to a shortened length, threaded & crowned, muzzles were dressed & blued, ...
05/08/2026

A pair came in for threading. Barrels were cut to a shortened length, threaded & crowned, muzzles were dressed & blued, bores were checked with indicator rods, and thread protectors were applied. Components were reassembled and rifles went out to customer. Quick turnaround on this pair. ready! Happy hunting!

Closing time…
04/30/2026

Closing time…

Head of Homeland Security. The G***k 41. I also rock the G34 on the other side of perimeter 🤓 Just slapped on some night...
04/29/2026

Head of Homeland Security. The G***k 41. I also rock the G34 on the other side of perimeter 🤓 Just slapped on some night sights by

Fitting a recoil pad is one of my favorite procedures. This old lever rifle also had a style optic mounted. Nice rifle...
04/24/2026

Fitting a recoil pad is one of my favorite procedures. This old lever rifle also had a style optic mounted. Nice rifle for any task. Happy hunting!!! & ya’ll have a great weekend!

Can you name that procedure? What’s going on with this old *****on model 11?
04/06/2026

Can you name that procedure? What’s going on with this old *****on model 11?

Address

Lafayette, LA
70508

Website

Alerts

Be the first to know and let us send you an email when Uncle B's Gunsmithing LLC posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share