Bare Metal Stripper

Bare Metal Stripper We are a premier coatings removal supplier

If you’re new to dip tanks: you don’t make “one waste.” You make a few different leftovers (spent bath, rinse water, slu...
03/24/2026

If you’re new to dip tanks: you don’t make “one waste.” You make a few different leftovers (spent bath, rinse water, sludge, wipes, empty drums, etc.).
When you dump it all together, you get Dumpster Stew — and that’s how disposal gets expensive and messy.

Run this 8‐step setup once:
✅ waste map
✅ one stream = one container
✅ drip zone
✅ liquids vs solids
✅ waste corner

For commercial use only • licensed businesses • W‐9 required.

03/22/2026

Re-dips don’t just cost labor... they blow up your whole board.

This is the goal:
controlled cycle → predictable rinse effort → fewer parts coming back.

If you want drums (or smaller quantities) and you’re a licensed business give us a call at 816-523-7466.
For commercial use only• W-9 required • Follow SDS.

🚨 Sale is on. Limited-time promoIf stripping is part of your weekly production, grab a barrel while it’s down.$1,050 bar...
03/21/2026

🚨 Sale is on. Limited-time promo
If stripping is part of your weekly production, grab a barrel while it’s down.

$1,050 barrels (was $1,250) + shipping
Same-day ship Mon–Thu before 12:00
•For commercial use only. W-9 required

03/20/2026

We sell throughput: predictable strip windows that keep blasting, prep, powder, and delivery on schedule.

If you’re a licensed business and want to order, give us a call at 816-523-7466.
For commercial use only• W-9 required

If you’re stripping powder coat with methylene chloride, this is your bare-minimum checklist.Not blasting. Not hot tank....
03/18/2026

If you’re stripping powder coat with methylene chloride, this is your bare-minimum checklist.

Not blasting. Not hot tank.
Methylene chloride.
Outside. Lid closed. No leaning. No solo work.
If you can’t check every box-don't open it.

B2B only • Licensed businesses • W-9 required

03/17/2026

If your crew has to ‘fight’ every wheel... you don’t have a stripping process. You’ve got a labor program.

When the bath is right + racking is right, it turns into:
dip → release → rinse → done

B2B only • W-9 required • Follow SDS.

$200 Off BarrelsQuick heads up — barrels are discounted right now.Good time to grab a barrel if you’ve been stretching w...
03/16/2026

$200 Off Barrels

Quick heads up — barrels are discounted right now.
Good time to grab a barrel if you’ve been stretching what’s left in the tank.
$1,050 (was $1,250) + same-day ship. Shipping is not included in price.

Mon–Thu before 12:00 pm
B2B only • W-9 required

Re-dips aren’t “just annoying.” They steal your schedule.If parts keep going back in the tank, it’s usually not the chem...
03/15/2026

Re-dips aren’t “just annoying.” They steal your schedule.

If parts keep going back in the tank, it’s usually not the chemical—it’s the process drifting:
✅ no set strip time
✅ temp wandering
✅ parts packed too tight
✅ bath getting dirty
✅ rinse getting lazy

If you’re evaluating a dip‐tank stripper built around predictable strip windows, Bare Metal Stripper is B2B only (licensed businesses only) and W‐9 required before shipment.

Safety note: coating removal is hazardous. Use ventilation/exposure controls and PPE per your SDS/EHS program. Trained staff only.

03/13/2026

Hot take: speed isn’t the main benefit. It’s knowing what’s going to happen before you drop the rim.

When strip time stays consistent, everything downstream stays on schedule.

B2B only • W-9 required • Follow SDS.”

Tank usually doesn’t “die.” It gets tired.And tired tanks don’t fail all at once... they start costing you re‐dips, brus...
03/12/2026

Tank usually doesn’t “die.” It gets tired.
And tired tanks don’t fail all at once... they start costing you re‐dips, brushing, and blown schedules.

Save this and run it once a week (takes 2 minutes).
If you land in DRIFTING, do the “known easy part” test before you blame the coating.

If you want help diagnosing it, DM us:
● what you’re stripping (wheels / racks / brackets)
● tank size (gallons)
● what changed (strip time, rinse time, brushing, re‐dips)

B2B only. Licensed businesses only. W‐9 required prior to shipment.

03/10/2026

Some wheels are built like they hate being stripped. 😅

The fix wasn’t hero scrubbing — it was process discipline:
✅ rack for drainage
✅ run a timer window (min/target/max)
✅ back in the tank if it’s not done

B2B only • W-9 required • Follow SDS.

Address

2401 E 85 Street
Kansas City, MO
64132

Opening Hours

Monday 8:30am - 4:30pm
Tuesday 8:30am - 4:30pm
Wednesday 8:30am - 4:30pm
Thursday 8:30am - 4:30am
Friday 8am - 12pm

Telephone

+18165237466

Website

Alerts

Be the first to know and let us send you an email when Bare Metal Stripper posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Bare Metal Stripper:

Shortcuts

Share

Category