Laguna Racing Engines

Laguna Racing Engines Located in Houston,Texas. We specialize in LS/LT and Gen 3 Hemi platforms .

Adan Pino put a monster together ‼️making crazy numbers N/A while sporting one of our 408”LS.641WHP @7100 and carries it...
02/10/2024

Adan Pino put a monster together ‼️
making crazy numbers N/A while sporting one of our 408”LS.

641WHP @7100 and carries it to 8000RPM !through a 4l80

-Texas Speed & Performance PRC 260 Heads with extensive modifications 🫢
-MAHLE 4.030” FT pistons
-Total Seal Piston Rings
-Callies Performance CCW 4.00” Crankshaft
K1 Technologies 6.125”H-beam Lightweight Rods
-King Racing bearings
-ARP
- performance CTS-V LS7 lifters
-Spike Performance and Tuning Rhino V3 cam

421” LS almost ready for dyno time 💻This power plant was built and spec’d almost 10 years ago so it was time for a fresh...
11/09/2023

421” LS almost ready for dyno time 💻
This power plant was built and spec’d almost 10 years ago so it was time for a freshen and few upgrades .Can’t wait to get this strapped down on the dyno and see what she puts down with a ProCharger P1X.
- COLA 4.125” Stroke crankshaft
- Eagle 6.125” H-Beam rods with arp 2000 rod bolts
- Custom Diamond 4.030” Pistons
- Total Seal Gas ported AP series rings
- Trend Performance Products Heavy wall .225 wrist pins and 3/8 .135” wall pushrods

- Bullet Racing Cams 247/258 .649”/.649” 114LSA

- Houston Performance Coatings, LLC Skirt coating and thermal coating on the crowns

- Ported SLP GM oil pump

- COMP Cams Double roller IWIS timing set & Rocker arms

- ARP Hardware all around.

- Hooper's heads 6 bolt Armadillo 265 cc heads with o-ring exhaust flanges with Hollow stem Stainless intakes and Inconel Exhaust .

-Black Market Racing A2W 105MM Sheetmetal Intake 😮‍💨

The offseason is coming so it’s time start planing on freshening your engine , don’t wait for winter as good machine shops tend to get super busy around this time .

Send us a PM contact us at
P # 832782445
Email: [email protected]
M-F 9:00AM - 6:00 PM

From now on I’ll be billing for troubleshooting engine problems unless I machined and assembled the WHOLE LONG BLOCK .Ti...
08/09/2023

From now on I’ll be billing for troubleshooting engine problems unless I machined and assembled the WHOLE LONG BLOCK .
Tired of fixing everyone’s else’s mistakes, and mishaps.

Also if I’m brought a engine to repair, after I had previously quoted you for the same build . There will be a 15-20 % labor rate increase on all machine work .

PFA :)

07/15/2023

We take pride in our craftsmanship here at LRE .We spend hours on blocks in just prep work before we even start machining. So Just because someone has a ridge reamer and a flex hone does not qualify them as engine builders .

With that being said here’s a clip of some of the prep work we do before we start honing .
By this time block is already squared decked with our BHJ decktru fixture to ensure our torque plates have a good flat surface to clamp to.
All blocks get the headbolts holes chased,
And a Torque plate is used with replicate hardware and gaskets it will be operating with .

06/03/2023

Little idle clip of that SBF with posted earlier.
She sounds real healthy 🔥

Hit us up for any engine or performance parts needs !

Email: [email protected]
P #: 8327824445
M-F 10AM-6PM
8210 Tomahawk trail 77050 Houston texas

A little diversity this week . Took on a SBF 302 project and wanted to do something out of the ordinary.The base started...
05/23/2023

A little diversity this week . Took on a SBF 302 project and wanted to do something out of the ordinary.
The base started with 289 block which we tried to keep it as original as we could but the Rods were seized and we couldn’t find any replacements
So we had to go with a 302 Rotating assembly .
But the real magic was in the top end, We modernized the valvetrain with GM LS parts
Valves , seals/locators and springs.
We also machined the heads for screw in studs and guide plates.

King Racing
Summit Racing Equipment
COMP Cams
Cometic Gasket, Inc.
Fel-Pro Gaskets

FOR SALE $2950 outrightGen 4 Iron 5.7 (5.3 bored to 3.898 LS1 Bore)24x-3.898 silvo-lite pistons and rings-LS7 style lif...
05/03/2023

FOR SALE $2950 outright
Gen 4 Iron 5.7 (5.3 bored to 3.898 LS1 Bore)24x
-3.898 silvo-lite pistons and rings
-LS7 style lifters and trays
-King Main/Rods/Cam bearings
-TSP MS3 Cam 238/242 .600/.600 112 LSA
-Reconditioned Gen 4 rods
-Bronze plug kit
-Melling 10295 Oil pump with Copo spring

Skip around the wait time this one is ready to go.
Can make it a long block for additional cost.

Another Hemi going out the 🚪 Was previously “rebuilt” by another shop but never ran right.We tried to salvage most of th...
05/03/2023

Another Hemi going out the 🚪
Was previously “rebuilt” by another shop but never ran right.
We tried to salvage most of the hard parts but we did have to go to a oversized piston to clean up the 0.0015 taper in the cylinder bores .
We also went ahead and added a Texas Speed & Performance 223/232 .582/.582 113 Camshaft
And deleted the MDS system .
King Racing bearings all around
Johnson Lifters drop in lifters
sealing it all up with Cometic gaskets all around .

Reach out to us for your engine needs

P #281-973-7393
Email:[email protected]
M-F 9am-6pm
8210 tomahawk trail 77050 Houston texas

Mopar guy by heart .So we had tons of fun building this one We put lots of love into IG Engine for his grocery getter M...
04/06/2023

Mopar guy by heart .
So we had tons of fun building this one

We put lots of love into IG Engine for his grocery getter

Modern Muscle Xtreme makes it easy for you Hemi guys
-426 stroker kit (6.4 Based)
Molnar Technologies Crankshaft 4.050”
Manley Connecting rods 6.125”
MAHLE Pistons 4.100”
Calico Bearings
ARP mainstuds

We also added MMX billet maincaps and plugged off the piston oil coolers to redirect oil to where we want it .
Come bulletproof your 6.4 with us !

8210 tomahawk trail 77050 Houston Texas
Email:[email protected]
P #: 281-973-7393
M-F 10-6pm

LRE 408 shortblock is the perfect For the budget weekend warrior guysProven to hold over 1000 horses 🐎these things can t...
03/22/2023

LRE 408 shortblock is the perfect For the budget weekend warrior guys
Proven to hold over 1000 horses 🐎
these things can take a beating week in week out .
Base starts with a seasoned 6.0 core
Callies Compstar 6.125 H-beam rods
Callies compstar 4.00” Stroke crankshaft
CP-Carrillo 4.030” Bullet series pistons
MAHLE/Clevite bearings all around
ARP Main studs

Base price starts at 6375.00 outright
Call us today for expanded pricing

P # 281-973-7393
Email: [email protected]
M-F 9am -6pm
8210 tomahawk trail 77050 Houston texas

Address

8210 Tomahawk Trail
Houston, TX
77050

Opening Hours

Monday 10am - 6pm
Tuesday 10am - 6pm
Wednesday 10am - 6pm
Thursday 10am - 6pm
Friday 10am - 6pm

Telephone

+18327824445

Website

Alerts

Be the first to know and let us send you an email when Laguna Racing Engines posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category