Apex Integration USA

Apex Integration USA Apex Integration LLC is a licensed electrical contractor in the state of Tennessee.

Wire duct filled to sixty percent is not a style choice. It is what lets the next person add a circuit without pulling t...
09/09/2026

Wire duct filled to sixty percent is not a style choice. It is what lets the next person add a circuit without pulling the whole harness. A multi-section control cabinet out of our panel shop. Power and control segregated, terminal strips labeled, I/O laid out in the order the drawing reads. The second frame is the part maintenance actually touches. Ferrules on every conductor, push-in terminals, and spare positions already landed and numbered. Nobody buys a panel for the inside. Everybody lives with it.

This Labor Day, we recognize the skilled people behind the technology, systems, and solutions that keep industry moving....
09/07/2026

This Labor Day, we recognize the skilled people behind the technology, systems, and solutions that keep industry moving. From engineering and programming to fabrication, installation, and integration, it takes experience and teamwork to turn complex challenges into reliable solutions. Thank you to the Apex Integration team, our partners, and the hardworking people across the industries we serve.

Happy Labor Day from Apex Integration.

The cheapest defect is the one that never leaves the station. Sensor and camera checks mounted along an overhead conveyo...
09/04/2026

The cheapest defect is the one that never leaves the station. Sensor and camera checks mounted along an overhead conveyor, confirming the right part is in the right carrier, facing the right way, before it moves downstream. Error proofing is not a camera. It is a decision about where you are willing to find the mistake. On the line it costs minutes. At the customer it costs a program.

Where does your line find its defects today?

09/02/2026

One operator, several spindles, and nobody standing at a door waiting for a cycle to end. A robot loading and unloading CNC machines at a precision machining shop. Raw stock in, finished part out, doors and chucks handled inside the cell. Machine tending is the easiest automation to justify and one of the easiest to get wrong. Part presentation and door interlock timing decide whether the robot removes an operator from the machine or just moves the waiting somewhere else.

08/28/2026

End of line is where labor hurts most. It is also where automation pays back fastest. Robotic palletizing and case handling we installed for a food and beverage producer. Consistent pattern, consistent stack height, nobody lifting cases for eight hours. Sound on if you like the rhythm of a line that is dialed in.

Empty building in the spring. Running line by fall. Extrusion-framed conveyor and station structure going in on a greenf...
08/26/2026

Empty building in the spring. Running line by fall. Extrusion-framed conveyor and station structure going in on a greenfield assembly line. Bonded and grounded, leveled, and laid out before a single controller was powered up. The unglamorous weeks are the ones that decide whether launch is calm or chaotic.

08/19/2026

One robot per press, down the line. Each KUKA arm carries a take-out frame matched to a single part geometry, reaching into the open mold, lifting the part off the core, and setting it down outside the guarding before the clamp closes again. Automation on this scale sets the building before it sets the cell: slab and power for the presses, an overhead monorail for mold changes, clear envelopes for the guarding.

The robot gets the credit. The tooling does the work. Custom end-of-arm tooling we designed and built in January to pick...
08/18/2026

The robot gets the credit. The tooling does the work. Custom end-of-arm tooling we designed and built in January to pick a large stamped panel. Pneumatic clamps, locating pins, and a frame stiff enough that the part lands in the same place on cycle 40,000 as it did on cycle one. If a cell is dropping parts or drifting out of tolerance, nine times out of ten the program is not the problem. The tooling is.

A panel is a document. Someone is going to read it at 2 a.m. with a flashlight. Safety controller, safety relay, disconn...
08/14/2026

A panel is a document. Someone is going to read it at 2 a.m. with a flashlight. Safety controller, safety relay, disconnect, 24V supply, wire duct routed so the door can actually close on a full harness. Built in-house earlier this year for an automotive component plant.

We lay out to the technician, not to the drawing. Room for a meter probe. Labels that face the person opening the door. Spare terminals, because there is always a phase two.

Two robots, one weld gun, and a tip dresser that runs on a schedule nobody has to remember. This is a multi-robot spot w...
08/12/2026

Two robots, one weld gun, and a tip dresser that runs on a schedule nobody has to remember. This is a multi-robot spot weld cell we rebuilt this spring for a Tier 1 stamping supplier. The part gets loaded, clamped and welded without an operator inside the fence.

Everybody asks about cycle time first. We ask about tip dress intervals, gun access, and how fast a tech can get to the weld controller, because that is what decides whether you hit your numbers in month eleven, not week one.

Address

170 Factory Street
Gallatin, TN
37066

Opening Hours

Monday 8am - 5pm
Tuesday 8am - 5pm
Wednesday 8am - 5pm
Thursday 8am - 5pm
Friday 8am - 5pm

Telephone

+16154206511

Website

Alerts

Be the first to know and let us send you an email when Apex Integration USA posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Apex Integration USA:

Shortcuts

Share

Category