Crazydayz Fab

10/18/2026

This huge 1979 F150 on 44s came in for a Bolt on helper bag kit for the rear.

Whipped up some upper and lower brackets made out of 1/4 steel plate.

Used some slam specialties SS8s

Bolted everything up and tested it.

As I always say, watch the YouTube videos!
I don’t take as many pics as I do videos 😉🫣

Go check it out!
Subscribe if you aren’t already 🙏

https://youtu.be/PXcRm4mfEhc?is=Dj3H22WD-HpF_j_d

10/13/2026

https://youtu.be/qcoyZwWygNg?is=7mrGspmL6qP3HYcJ

In this episode:I attend Slamfest and compete in the limbo compet...

10/12/2026

Another successful trip to Slamfest Truck & Car Show

New motor did great towing 🥳

The chop took home another limbo trophy 🏆

Chatted with tons of awesome people 😃

Saw a bunch of amazing quality rides!!

Here are just a sample of what was there!!!

Tons more in the video!!!!

As I always say, watch the YouTube videos!

I don’t take as many pics as I do videos 😉🫣

Go check it out!
Subscribe if you aren’t already 🙏

https://youtu.be/qcoyZwWygNg?is=MdwX0GWj-s9UJuTl

10/05/2026

Dyno tune time!!

Truck runs great!!

Maxed out the stock truck injectors at 4k RPM 😂

Going back tomorrow to do it again after throwing some 50lb injectors in once i get there.

The truck developed a slight hard start so I threw a fuel bump in 👌

Stay tuned to my story and YouTube!! Might go live or make some shorts… 🤔

As I always say, watch the YouTube videos!
I don’t take as many pics as I do videos 😉🫣

Go check it out!
Subscribe if you aren’t already 🙏

https://youtu.be/FvVRYiae0yI?is=7ABhJfRP3pRgQhtT

09/28/2026

Next one up!!!

2025 single cab ford f150 owned by Daniel Soto

It needed a Ridetech drop kit installed.

Tore the front struts and upper control area out.

Replaced them with the Ridetech upper arms and coilovers.

The rear wasn’t too bad except for the typical seized wheels to the hubs 🤦‍♂️

Got the rear leafs pulled, bolts flipped and the new parts installed.

Can’t thank everyone for the continued support 🙏

As I always say, watch the YouTube videos!
I don’t take as many pics as I do videos 😉🫣

Go check it out!
Subscribe if you aren’t already 🙏

https://youtu.be/UJiLiE3fNKU?is=s3eYQpBE7ee_LSJG

09/20/2026

Motor is in!! 👏

Everything went back in smoothly.

Fired right up!! 😈

Topped off the coolant!

Currently doing the a/c 🥶

Test run next!!!! 🤪

As I always say, watch the YouTube videos!
I don’t take as many pics as I do videos 😉🫣

Go check it out!
Subscribe if you aren’t already 🙏

https://youtu.be/EnMx6veVX9Y?is=M5nzxRHXoLbVtQNz

09/15/2026

Motor is ready to drop into Pete… 👏

Got everything tore down and cleaned up on the outside.

I didn’t have to clean the inside of this motor because it had low miles and was well taken care of…

Pulled a few broken exhaust studs.

Pulled the old parts to put in the new stage 2 cam, springs, oil pump and timing set.

Everything was torqued to spec 🫡

As I always say, watch the YouTube videos!
I don’t take as many pics as I do videos 😉🫣

Go check it out!
Subscribe if you aren’t already 🙏

https://youtu.be/TeZMr-xdIN0?is=tsKjha2FEUG1GLLc