Crum‘s Manufacturing Services

Call Directions Website

Crum‘s Manufacturing Services Welding, Machine Shop, and Hydraulic Services!

Back rack clean out! Today we cleaned the back of the metal rack off and looking to move our shorts pile! There are many...
07/22/2026

Back rack clean out! Today we cleaned the back of the metal rack off and looking to move our shorts pile! There are many sizes to be had here:

3“ Channel
4“ Channel
2“ Angle
3“ Angle
4“ Angle
Many sizes of tube flats and round bar

This is a buyer take all deal at $750. Cash, Card, Check, Affirm. 3% fee on card transactions. There is a lot more value here than what we are asking. With metal on the rise like it’s been this skid is easily worth double that.

Customer had a key stock failure. The end of the shaft was worn down and the key way unable to perform its job. We welde...
02/25/2026

Customer had a key stock failure. The end of the shaft was worn down and the key way unable to perform its job. We welded up, turned down and remilled the part to bring it back into spec.

It’s hard to tell from the pictures but these are thread adaptors to go from 3/8“ fine thread to 1/2“ coarse thread made...
02/23/2026

It’s hard to tell from the pictures but these are thread adaptors to go from 3/8“ fine thread to 1/2“ coarse thread made from stainless steel.

Large Blind Fl**ge we added a 1/2“ NPT port to!
02/17/2026

Large Blind Fl**ge we added a 1/2“ NPT port to!

Hydraulic Cylinder Rods made for an antique Allis Chalmers
02/16/2026

Hydraulic Cylinder Rods made for an antique Allis Chalmers

New side rail for this truck fabricated and installed! The original one was involved in an accident with a telehandler a...
02/13/2026

New side rail for this truck fabricated and installed! The original one was involved in an accident with a telehandler and was no longer functional.

Some photos of recent jobs done related to hydraulics. We make custom hose assemblies while you wait! 1/4“ to 1 1/4“ two...
02/12/2026

Some photos of recent jobs done related to hydraulics. We make custom hose assemblies while you wait! 1/4“ to 1 1/4“ two wire assemblies with bite to crimp ends! Also 1/2“ to 1 1/4“ four wire assemblies for those more severe applications! We stock JIC, Pipe, O-Ring Boss, Face Seal, Fl**ge, Metric, Banjo, and so many more styles!

We also rebuild hydraulic cylinders with quick turn arounds available!

Hydraulic Valves available for order!

Stainless steel boxed lid with hingeing grates to separate larger pieces. Heavy hinges in stainless steel could not be p...
02/11/2026

Stainless steel boxed lid with hingeing grates to separate larger pieces. Heavy hinges in stainless steel could not be procured in time for this project so we had to make them ourselves. We also installed this peice for our customer.

Emergency! That’s what the customer said when they called on a Saturday night to see if we were available to do this job...
01/30/2026

Emergency! That’s what the customer said when they called on a Saturday night to see if we were available to do this job. This was for a local frac company who needed these ni***es welded on the tank so they could flow fluid through this container. We prepped the ni***es with a good bevel on the lathe then plasma cut a hole and started welding!

Before and after! We redone the fenders on this trailer and added some extra long steps to assist the driver. These fend...
01/29/2026

Before and after! We redone the fenders on this trailer and added some extra long steps to assist the driver. These fenders were built heavier than the standard manufactured ones and should out last the useful life of this equipment.

Address

Bethesda, OH
43719

Telephone

(740) 391-5307

Website

Alerts

Be the first to know and let us send you an email when Crum‘s Manufacturing Services posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category