Distar LTD

Distar LTD Distar official. Professional production of diamond tools since 1994.

💦 Cover — cool the blade and localize waterDoes water become a problem when working with Proxxon small engraver machines...
13/06/2026

💦 Cover — cool the blade and localize water

Does water become a problem when working with Proxxon small engraver machines? Cover is the solution.

Designed for diamond blades up to 50 mm in diameter, Cover uses only 50 ml of water per minute of operation 💧 The quick-release nozzle can be used outside the guard when working with diamond wires or drills.

🛡️ A rubber splash guard helps contain water within the cutting area and reduces unwanted splashing. The protective casing features adjustable extension length, allowing use with the Support adapter or with standard collet adapters supplied with the blade.

🔄 Cover can be mounted for both left-hand and right-hand operation. It delivers the best performance when used with Butterfly or ButtonCut blades 🦋⚡

Specifications:
🔹 Compatibility: Proxxon small engraver machines
🔹 Maximum blade diameter: 50 mm
🔹 Water consumption: 50 ml/min
🔹 Quick-release nozzle
🔹 Adjustable guard extension length
🔹 Left- and right-side installation
🔹 Compatible with Support adapter and standard collet adapters

Cover — keep the blade cool, the cut clean, and the water under control. ✨

12/06/2026

🚀 Forget about grinding. Create the flush button three times faster.

The production of ceramic elements for bathrooms and kitchens is a labor-intensive and time-consuming process. Making installation buttons, switches, sockets, and other elements usually requires several hours of precise work. After cutting, accurate grinding of chips is needed, leaving no room for error.

💎 The 50 ButtonCut blade is a solution that reduces the process several times. Fine diamond grain and a blade thickness of just 0.8 mm provide a clean cut without chips. Grinding is no longer required, significantly speeding up and simplifying the work.

✨ Finished products look professional and flawless.

Experience a new level of speed and perfection.

🔹 Application: cutting flush buttons, switches, sockets, and other ceramic elements
🔹 Blade thickness: 0.8 mm
🔹 Operation mode: with water supply 💦
🔹 Recommended speed: around 10,000 rpm
🔹 Compatibility: small engraver machines

⚠️ Please note:

✔️ For best results and to prevent chipping, reduce the speed to around 10,000 rpm.
✔️ A sufficient water supply must be maintained at all times. Even a slight reduction in water supply can cause chipping.
✔️ Hand sprayers are not recommended. The Cover attachment is the best option, as it is installed on the small engraver machine and provides a constant water supply.
✔️ Battery-powered water supply devices are recommended.
✔️ Use the Support adapter for the small engraver machine. It helps reduce vibration and improves accuracy.
✔️ For best results, place the tile on a vibration-absorbing material, such as polystyrene foam or similar.

🚀 Forget about grinding. Create the flush button three times faster.The production of ceramic elements for bathrooms and...
11/06/2026

🚀 Forget about grinding. Create the flush button three times faster.

The production of ceramic elements for bathrooms and kitchens is a labor-intensive and time-consuming process. Making installation buttons, switches, sockets, and other elements usually requires several hours of precise work. After cutting, accurate grinding of chips is needed, leaving no room for error.

💎 The 50 ButtonCut blade is a solution that reduces the process several times. Fine diamond grain and a blade thickness of just 0.8 mm provide a clean cut without chips. Grinding is no longer required, significantly speeding up and simplifying the work.

✨ Finished products look professional and flawless.

Experience a new level of speed and perfection.

🔹 Application: cutting flush buttons, switches, sockets, and other ceramic elements
🔹 Blade thickness: 0.8 mm
🔹 Operation mode: with water supply 💦
🔹 Recommended speed: around 10,000 rpm
🔹 Compatibility: small engraver machines

⚠️ Please note:

✔️ For best results and to prevent chipping, reduce the speed to around 10,000 rpm.
✔️ A sufficient water supply must be maintained at all times. Even a slight reduction in water supply can cause chipping.
✔️ Hand sprayers are not recommended. The Cover attachment is the best option, as it is installed on the small engraver machine and provides a constant water supply.
✔️ Battery-powered water supply devices are recommended.
✔️ Use the Support adapter for the small engraver machine. It helps reduce vibration and improves accuracy.
✔️ For best results, place the tile on a vibration-absorbing material, such as polystyrene foam or similar.

Grinding porcelain stoneware is one of the most time-consuming stages — especially when using low-power angle grinders.B...
02/06/2026

Grinding porcelain stoneware is one of the most time-consuming stages — especially when using low-power angle grinders.
But not with NECTAR! 💥

💎 Chip-free grinding
⚡ High speed
🔥 No motor overheating
🎯 Perfect for hard-to-reach places (Ø45 mm / 5.8 mm bore)

NECTAR – a small tool with powerful results! 💪


✨ Enjoy perfectionThe wide variety of porcelain stoneware types requires a diverse selection of diamond tools 🔧 The Soft...
01/06/2026

✨ Enjoy perfection

The wide variety of porcelain stoneware types requires a diverse selection of diamond tools 🔧 The Soft Edge 45 engraver milling cutter is specially designed for processing the most demanding tiles 💎

The diamond layer is cooled with graphite chips ❄️ completely eliminating chipping. Ideal for grinding glazed or fragile porcelain stoneware ✨

It features an outer diameter of 45 mm and a mounting hole of 5.8 mm ⚙️ It performs best at maximum speed 🚀 Designed for use with engravers 🛠️

Soft Edge 45 — complex tasks with jeweler’s precision 💍

🌀 Cord Diamond WireNEW CURVE!Cutting radiuses in porcelain stoneware is usually a difficult and time-consuming process c...
22/05/2026

🌀 Cord Diamond Wire
NEW CURVE!

Cutting radiuses in porcelain stoneware is usually a difficult and time-consuming process caused by the limitations of existing diamond tools ⚙️

Cord Diamond Wire is a new high-performance solution 🚀

This premium diamond wire has a thickness of just 0.5 mm and is manufactured using multi-layer electroplating technology 💎 Its lifetime is up to 6 times longer than standard wires on the market, while cutting speed is up to 50% faster ⚡

Cutting a 12 mm radius takes only 4 minutes ⏱️ and the lifetime of one 30 cm wire reaches 12–18 cm of cutting, depending on tile thickness and cooling quality 💦

The wire significantly speeds up the creation of popular porcelain stoneware elements, such as:
🔹 flush plate openings
🔹 ventilation holes
🔹 inspection hatches
and more

It also allows quick trimming of corners after cutting with diamond blades ✨

Cord Diamond Wire is a new turn in boosting tiling productivity 🔥

The set includes:
5 pcs of 30 cm wires 📦

22/05/2026

CordSET — a set for radius cutting in porcelain stoneware 🔄

A new turn in tile work 💎

Cutting radii or 90° corners in porcelain stoneware is a complex task that requires skill and precision. And the most difficult part — there is no room for mistakes.

CordSET makes radius cutting faster, easier, and accurate from the very first attempt ⚡

Cutting is performed with a high-quality 0.5 mm diamond wire. The cutting direction is guided by a hardened steel template, fixed with specially designed clips and wedges. The wire is quickly secured in comfortable handles, and the set includes a highly absorbent sponge for water cooling 💦

To prevent cracks on corners or radii during work, the tile is fully fixed from all sides with specialized clips.

The core of the set is a premium diamond wire made using multilayer diamond coating technology. Its lifetime is up to 6 times longer than standard wires on the market, while cutting speed is up to 50% higher 🚀

Cutting a 12 mm radius takes only 4 minutes. The lifetime of one 30 sm wire reaches 12–18 cm of cut, depending on tile thickness and cooling quality.

CordSET significantly speeds up the production of popular porcelain stoneware elements, such as:
installation button cut-outs
ventilation openings
inspection hatches
and more

CordSET diamond cutting set — a new turn in tile work productivity.

Set includes:
5 diamond wires, 30 sm each
1 template for cutting 3, 6, and 12 mm radii
2 quick-fixing handles
20 specialized clips
4 plastic wedges
1 highly absorbent sponge

CordSET — a set for radius cutting in porcelain stoneware 🔄A new turn in tile work 💎Cutting radii or 90° corners in porc...
21/05/2026

CordSET — a set for radius cutting in porcelain stoneware 🔄

A new turn in tile work 💎

Cutting radii or 90° corners in porcelain stoneware is a complex task that requires skill and precision. And the most difficult part — there is no room for mistakes.

CordSET makes radius cutting faster, easier, and accurate from the very first attempt ⚡

Cutting is performed with a high-quality 0.5 mm diamond wire. The cutting direction is guided by a hardened steel template, fixed with specially designed clips and wedges. The wire is quickly secured in comfortable handles, and the set includes a highly absorbent sponge for water cooling 💦

To prevent cracks on corners or radii during work, the tile is fully fixed from all sides with specialized clips.

The core of the set is a premium diamond wire made using multilayer diamond coating technology. Its lifetime is up to 6 times longer than standard wires on the market, while cutting speed is up to 50% higher 🚀

Cutting a 12 mm radius takes only 4 minutes. The lifetime of one 30 mm wire reaches 12–18 cm of cut, depending on tile thickness and cooling quality.

CordSET significantly speeds up the production of popular porcelain stoneware elements, such as:
installation button cut-outs
ventilation openings
inspection hatches
and more

CordSET diamond cutting set — a new turn in tile work productivity.

Set includes:
5 diamond wires, 30 sm each
1 template for cutting 3, 6, and 12 mm radii
2 quick-fixing handles
20 specialized clips
4 plastic wedges
1 highly absorbent sponge

20/05/2026

Looking for a blade for a clean cut on any type of tile? Shine diamond blade with a thickness of 0.6 mm! ✨

Perfect 90° cutting line.
Maximum clean edge without unnecessary defects.
Minimum chipping even on difficult porcelain stoneware.
Stable result on matte, glossy, and textured tiles 💎

Shine blades are available in diameters:
125 mm — for long cuts
101.6 mm — for small cut-outs
76 mm — for small angle grinders and precise work in hard-to-reach areas.

You can buy the Shine blade and Spray cooling system on the website or from distributors in your city! 💦

Address

45A Reshetylivska Str
Poltava
36007

Opening Hours

Monday 09:00 - 17:00
Tuesday 09:00 - 17:00
Wednesday 09:00 - 17:00
Thursday 09:00 - 17:00
Friday 09:00 - 17:00

Website

Alerts

Be the first to know and let us send you an email when Distar LTD posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Distar LTD:

Shortcuts

Share

Category