SweBend

Name: SweBend
Address: Belevägen 6, Hässleholm, 28143, SE
Telephone: +46709705160

The strongest, most sophisticated and most reliable bending machines on the market, worldwide. The n

08/09/2026

Tougher material and tighter radii makes your bends increasingly difficult. SEVEN X is intelligent automation on the machine. It reads the work and corrects while you are still rolling.

- IRMA watches the radius, stores the correction, and keeps the rest of the batch in shape.

- SURE, Surface Uniformity and Radius Evaluation, reads edge and radius together. Watch it on the PB4-8-6 in Hannover.

The same control goes on a new SweBend, or onto the bender already on your floor. Analog to CNC in about three days, including tuning and operator training. We have been developing, enhancing and upgrading this software since the 1980s.

Come meet us at your closest exhibition:

EUROBLECH, 20-23 October in Hannover, with Venema Biegetec GmbH at Hall 11, Stand 11-E01.
https://swebend.com/euroblech/

FABTECH, 21-23 October in Las Vegas, with Trilogy Machinery, Inc., INC. at Booth C-2032.
https://www.trilogymachinery.com/events/

Read more about the SEVEN X here https://swebend.com/cnc/

SweBend - Built around YOUR Bend.

24/08/2026

Want to see what SweBend can do for your operation? Watch this Linders review!

Fabricating & Metalworking Magazine visited Linders Specialty Company, Inc in the United States, where SweBend's bending machines are part of their daily production.

The rolls are engineered with robust shafts and SKF bearings for the highest drive torque on the market. Running them is the award-winning SevenX CNC control, with a graphical interface and multi-axis precision for repeatable results.

Full-service support from Trilogy Machinery, Inc. our exclusive distributor in North America.

13/08/2026

This VSB3-70 recently left the factory.

A variable geometry section bending machine, on its way to GVB Infra in Amsterdam - the operator that maintains the city's tram and metro network. It will bend large rail sections for track renewal.

Uprated for the job: drive torque and rolling speed increased for the heaviest rail profiles, up to 12 m/min, and SEVEN X Gold CNC with IRMA reading and adjusting the rolling radius automatically.

Sold through J. Venema Bv, our partner for the Netherlands, Belgium and Luxembourg.

SweBend - Built around YOUR Bend.

30/07/2026

SB3X-140, one section bender doing two jobs: support rings on one end of the envelope, tight-ID flat-bar spirals on the other.

Read the full case: https://swebend.com/case/sb3x-140-square-rectangular-bar-bending-spray-engineering/

17/07/2026

SB3X-140: One machine. Two bends.

Day to day: large support rings for pressure vessels, with consistent ring geometry, short flat ends, full diameter range from 1,500 to 6,100 mm.

At the limit: 100 x 30 mm S355 flat bar spiraled to inside diameter 500 mm. A tight ID for that section size, where the bar is being deformed to a radius only a few times its thickness, and both side-roll force and drive torque have to stay high through the entire bend.

We built the SB3X-140 for Spray Engineering Devices Limited, a sustainability-focused manufacturer of process equipment for sugar refineries, biofuel and wastewater industries. It's a heavy-duty section bending machine configured with horizontal shafts for vertical bending, a special roll set for square and rectangular bar, hydraulic lift and pitch on both sides of the machine, and a calibration unit for final geometry.

It's shipped with the Wireless Bluetooth Control Unit, so the operator stays close to the workpiece, whether the bend that day is a pressure-vessel ring or a tight spiral.

The result:
* Production ring bending across 1,500 to 6,100 mm on the same machine
* 100 x 30 mm S355 flat bar spiraled to ID 500 mm in a single setup
* Short flat ends after pre-bend, less scrap per ring
* Roll sets that can be swapped as Spray's product mix evolves; the machine stays in service

Spray's positioning is "zero carbon emissions, zero energy waste". Ours is machines that last decades and adapt to new tooling. Same logic, applied at different points in the value chain.

Read the full case: https://swebend.com/case/sb3x-140-square-rectangular-bar-bending-spray-engineering/

SweBend - Built around your bend.

02/07/2026

Peter Nilsson beside the recently built SB3X-140 for Spray Engineering Devices Limited. It's equipped with a Wireless Bluetooth Control, enabling the operator to freely move around the workpiece while a 150 x 30 mm S355 flat bar is bent to progressively tighter radii (R1250, R1000, R850).

Read the full case here: https://swebend.com/case/sb3x-140-square-rectangular-bar-bending-spray-engineering/

SweBend - Built around your bend

22/06/2026

What can bend special sections with up to 45t bending force - and still bend them with precision? A custom, variable-geometry section bender, engineered in Sweden to the exact spec of STURM Metallbearbeitung

It's wrapped, crated and ready. Eine weitere neue Maschine für Sturm - lassen Sie sich überraschen.

A project with our partner Venema Biegetec GmbH

18/06/2026

Another SweBend PB3-14-10 plate roll is up and running - this time in Taiwan.

Commissioned together with our partner Metech, who handled the local installation and service on the ground. Strong agents like Metech are how a machine built in Sweden runs reliably on the other side of the world.

The PB3-14-10 is a three-roll, all-hydraulic plate bender built for heavy plate:
- Pyramid design with double-pinch pre-bending for short flats at both ends
- Independent hydraulic drive on all three rolls with automatic speed compensation, so torque holds without power loss
- Hardened & ground rolls (≈58 HRC) on SKF bearings for repeatable forming under load
- Wireless Bluetooth Control with digital readouts at both ends for fast, accurate setup

And this is what it looks like once it is properly installed in a real factory: the machine is recessed into a prepared foundation and fixed into the floor, so the loading height sits at floor level for easier, safer plate handling.

Designed and produced in Sweden. Delivered, installed and supported worldwide.

Read more about the PB3 series here: https://swebend.com/machines/plate-rolls/

04/06/2026

Heavy-duty joggling of pressure vessel cylinders in mild steel up to 15 mm using the SweBend JM-140 - a tailored forming machine that rolls profiled grooves into the cylinder body for strength, roundness, and pressure absorption, and joggles stepped flanges at the cylinder ends for welding - in the same setup.

Read the full case: https://swebend.com/case/jm-140-joggling-machine-spray-engineering/

Learn more: https://swebend.com

23/05/2026

Grattis till våra två medarbetare Odai och Daniel som idag sprang Göteborgsvarvet, världens största halvmaraton!

Adress

Belevägen 6
Hässleholm
28143

Telefon

+46709705160

Webbplats

http://www.swebend.com/

Aviseringar

Var den första att veta och låt oss skicka ett mail när SweBend postar nyheter och kampanjer. Din e-postadress kommer inte att användas för något annat ändamål, och du kan när som helst avbryta prenumerationen.

Kontakta Affären

Skicka ett meddelande till SweBend:

Vill du placera din affär längst upp i Utrustningföretag-listan i Hässleholm?