Weber Packaging Solutions

Home
United Kingdom
Tranent, Scotland
Weber Packaging Solutions

Directions Website

Weber, one of the world’s premier label manufacturers, provides comprehensive

15/10/2026

Somewhere in most product launches there is a moment when the pack design gets signed off and someone says, "now we just need a label for it". That is usually the expensive moment, because the pack has already decided where the label can go.

A curved shoulder, a seam in the wrong place, a textured finish or a tapered tub all change what a label can do. Ten minutes spent on label placement while the pack is still on the drawing board removes problems that would otherwise turn up on the line. Our label design and consulting team is glad to be asked early, and it is a far easier conversation to have at that stage.

📩 Planning a launch? Bring us in early: https://zurl.co/dUpCW

08/10/2026

How much can you fit on a small pack before it stops being legible? On a sleeve, a small carton or a narrow panel, the answer is usually less than the design team would like.

The Markoprint Integra PP RAZR is built for that tight spot. It prints at up to 600 dpi vertically, handles small fonts from 1.5 mm, and copes with logos and grey-scale graphics as well as text. It also keeps up, running at up to 90 m/min at 300 dpi, so the line does not slow down to make room for a good-looking code. Coding sits beside your labels and does the part a label cannot reach.

➡️ See the Markoprint Integra PP RAZR: https://zurl.co/iJnHv

07/10/2026

A pallet with one product on it is easy to label. A mixed pallet, built for a store order from a dozen different lines, is a different job.

The label has to say what is on it, in a form that a scanner and a person can both check, and it has to be right when the pallet is built and not corrected later. A pallet label printed at the point of building, from the order data, saves the guesswork and the hand-written additions in the margin. It also makes goods-in at the other end a lot quicker for everyone involved.

Mixed pallets are where label accuracy earns its keep.

👉 Retail solutions: https://zurl.co/qB6Tb

29/09/2026

The Weber Alpha HSM is a modular, servo-driven label applicator that can be configured to fit almost any packaging line.

💡 Modular design, that can be adapted to new products and expanded later
✅ Label widths from 10mm to 320mm
✅ IP65 rated for dust and splashing water
✅ Tandem operation for zero-downtime labelling

👉 See the Weber Alpha HSM: https://zurl.co/Jikvd
📩 Tell us your label size, line speed and pack, and we will recommend the right configuration.

24/09/2026

A barcode that will not scan is rarely broken. Far more often it is a contrast or a surface problem. Scanners read the difference between dark bars and light gaps, so black on white is the safe standard, and the tempting design choices are where it goes wrong. Red bars can read as blank, because the scanner's red light bounces off them. Pale on pale, or dark on dark, leaves too little contrast to read at all. Metallic and clear films throw the reader off in their own way.

The surface matters as much as the colour. A code needs the right print method for the material it sits on, so it stays crisp rather than spreading or rubbing off. Get contrast and surface right and the scan stops being a lottery.

👉 If a code keeps failing and no one can say why, we can look at it: https://zurl.co/4fYn8

23/09/2026

⏱ Picture a line filling ten bottles a second. A label roll runs out, someone changes it, and five quiet minutes go by. That is roughly three thousand bottles that came past with nowhere to put a label. On a fast line, an ordinary roll change is not a pause, it is a hole in the day's output.

Zero-downtime labelling closes that hole. A second labeller sits downstream and takes over the instant the first one stops, so nothing goes past unlabelled and the line never waits for a roll. On the highest-volume lines the two can run in tandem to lift throughput as well. The point is simple: the labelling step should never be the reason a fast line stops.

👉 If roll changes are costing you output, there is a way round it: https://zurl.co/0ZzuP

22/09/2026

📡 The usual assumption about a barcode is that someone has to see it to scan it, one at a time, each label square to the reader. For a lot of operations that is fine. When the volumes climb, it quietly becomes the bottleneck.

An RFID label does not need line of sight. Each one carries a tiny chip and antenna holding a unique code, and a reader can pick up many of them at once, through packaging, without a clear view of any single label. A whole cage or pallet can reconcile in seconds rather than being unpacked and scanned item by item. It does not replace the barcode everywhere, but where bulk reading and speed matter, it changes what a labelling step can do.

👉 If counting stock is slowing you down, RFID may be worth a conversation: https://zurl.co/GAFWe

18/09/2026

🔬 Some of the hardest labels we deal with are also the smallest. A sample vial can be a few millimetres across, curved, and about to spend its life in a freezer, an autoclave or a splash of solvent. The label has to hold on to that tiny curved surface, survive all of it, and still be perfectly legible when someone picks it up weeks later.

That is not a job for an ordinary label and a marker pen. It takes a material soft enough to wrap a narrow tube, an adhesive rated for cryogenic cold or high heat, and thermal-transfer print that will not smear, fade or lift. Get the barcode on there reliably and you get fast, accurate identification of every sample; get it wrong and you have an unreadable tube and a real problem. Small does not mean simple.

👉 If your lab labels lift, smear or fade, we can match ones that will not: https://zurl.co/29pNP

17/09/2026

📈 The busiest weeks are the worst time to discover your labelling cannot keep up.

Volume finds the weak point: the slow changeover, the code scanning at ninety-five per cent, the roll that runs out. Better found in September than in December.

👉 Swipe through to stress-test yours before peak. If something's not holding up, we can take a look with you: https://zurl.co/XMxUB

11/09/2026

❄️ Here is a labelling problem that gets solved the wrong way almost every time. A label keeps lifting at the corner on a chilled pack. The obvious answer is a stronger glue, so someone orders a stronger glue, and a few weeks later the corner is lifting again.

The glue was never the problem. A cold, slightly damp surface needs an adhesive designed for cold, damp surfaces, not simply a more aggressive one. Match the adhesive to the temperature and the moisture and the corner stays down, quietly, for the life of the product. It is a smaller change than most people expect, and unlike the stronger glue, it lasts.

👉 If your labels lift in the chiller, we can match one that will not: https://zurl.co/JvSBX

Address

Macmerry Ind Est
Tranent
EH331HD

Website

http://www.weber.co.uk/

Alerts

Be the first to know and let us send you an email when Weber Packaging Solutions posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Want your business to be the top-listed equipment service in Tranent?