M.T. Engineering

Call Directions

M.T. Engineering Steel fabrication, agricultural engineering and machinery repairs

Made the most of the good weather last week and got the Strautmann wagon sandblasted and re sprayed 👌🏼
27/09/2026

Made the most of the good weather last week and got the Strautmann wagon sandblasted and re sprayed 👌🏼

Re line plates made and welded in to this Kuhn Profile mixer wagon. This went in really nice 👌🏼
20/09/2026

Re line plates made and welded in to this Kuhn Profile mixer wagon. This went in really nice 👌🏼

One I did a while back, Deemed to be un repairable by Main dealer. A Claas header drive gearbox had stripped the threads...
31/08/2026

One I did a while back, Deemed to be un repairable by Main dealer. A Claas header drive gearbox had stripped the threads on the clutch retainer shaft, I cut the damaged threads off and drilled down through the centre of the shaft, cut internal threads and then made a replacement threaded unit to screw into the shaft, a roll pin prevented this from unscrewing when adjusting the clutch unit. This repair saved the customer thousands of pounds 👌🏼

Strautmann wagon currently being refurbished. New 6mm liner kit made and welded in as well as new buttresses. I have als...
21/08/2026

Strautmann wagon currently being refurbished. New 6mm liner kit made and welded in as well as new buttresses. I have also put 10mm on the floor which isn’t something I have done before but it has gone in well. This wagon will have new augers fitted. Dare I say it… I just need a week of nice weather to sand blast a re spray now 🫣

A drive coupling I machined to allow a McConnel trimmer rotor to be mounted in a rotor balancing machine. Machined on th...
17/08/2026

A drive coupling I machined to allow a McConnel trimmer rotor to be mounted in a rotor balancing machine. Machined on the lathe without turning the part to ensure everything was concentric, internal keyway cut and fl**ge divided, drilled and threaded👌🏼

Apologies for the lack of posts, it’s been ABSOLUTE CARNAGE !! A recent line boring job- an old school Farm master with...
16/08/2026

Apologies for the lack of posts, it’s been ABSOLUTE CARNAGE !! A recent line boring job- an old school Farm master with some pretty spectacular wear, now good as new with fresh bushes fitted 👌🏼

It not just Big parts I machine. This particular job, an obsolete spool valve collet required a Micro boring bar and fac...
07/06/2026

It not just Big parts I machine. This particular job, an obsolete spool valve collet required a Micro boring bar and face grooving tool to be used. Nothings impossible, Everything can be replicated, it has already been made once before 👌🏼

I had a lot of comments on the original Lucas liner kit I made a few years back. How’s this for an upgrade for the same ...
24/05/2026

I had a lot of comments on the original Lucas liner kit I made a few years back. How’s this for an upgrade for the same customer, this time not only was it a brand new Lucas castor + 80R but the customer also wanted 5mm 450 HARDOX plate used as well as 8mm 450 HARDOX on the flywheel 🥵 hopefully this will last a few years of 25 bales a day through her. The chute sections were also lined but unfortunately I lost the pictures. 🌾🌾🐄

The second Stainless steel bottle pre wash table I have made for a local dairy 🐄 🥛
04/05/2026

The second Stainless steel bottle pre wash table I have made for a local dairy 🐄 🥛

JCB handler in for a headstock pivot line bore 👌🏼
29/04/2026

JCB handler in for a headstock pivot line bore 👌🏼

Address

Exeter
EX5

Telephone

07779012077

Website

Alerts

Be the first to know and let us send you an email when M.T. Engineering posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category