AMA Services

31/12/2024

Hi, all😁 I have got this homemade plastic roll dispenser with a lot of heavy duty plastic roll left on it here at the workshops also. Very useful for packing shipped items, weatherproofing stuff, etc. Message me with offers on it and collection is necessary from SA18 1PA. Thanks!

31/12/2024

Hi guys n gals, I’ve also got theses 3 well-built wooden shelves which are way smaller than the pallet shelves I’ve posted for sale before this post. (I’ve got two stacked in the rear so they are all the same size, and will reconfigure to go along a wall in a home workshop, shed, etc easily.) £100 takes all three, contact me for collection info 😁👍

31/12/2024

Any use to anyone out there? I’m closing down my workshop after darned near 20 yrs in the UK servicing the needs of our American vehicle owners, and are liquidating a few workshop items as they open up. We have four of this type of heavy duty pallet shelving system available with varying number of shelves(3 have 3 shelves as shown, & one has 4 shelves on it) for £100 each, including wood shelves. Will easily accept multiple engines on pallets so will easily handle whatever you throw at them, weight-wise! I also have one set of heavy duty grey shelves like this which are shorter in length, and about a foot deeper from front to back, set up in 3 shelf configuration, including the wood for £100 which I will post as I empty it out. Message me for one or more of these big guys! Thanks & an early Happy New Year to everyone! 😁😁😁

29/02/2024

Happy Leap Day, folks! Check the date😁

29/12/2023

Yep, I’ve seen it happen a couple of times during my career. RTV is the worst in bolt holes, always clean em out!

The importance of cleaning out liquid in your holes before torquing headbolts

04/07/2023

Happy Independence Day y’all! 💯😄💥💥💥

11/04/2023

A little video of the lean, mean Corvette 350 cu in V8 after it’s conversion to carburettor, list of tasteful mods. Check her out😍

11/04/2023

Finally got back to my own 82 Corvette project. Swapped out the limited factory Crossfire Injection for Edelbrock performance parts, dual roller timing set to replace stretched original single row timing set, vacuum advance HEI with 65k volts & a performance spark module in place of the factory computer controlled HEI. Also swapped out the factory low compression heads for a set of 1970 Corvette camel hump heads to raise the compression ratio and put some pep in her step! Runs great, should be more grunt on tap😁 Haven’t driven it yet as I’ve only just finished the fine tuning of the Edelbrock 650cfm carb and choke/cooling fan operation. Hope to be taking her to the next brunch meet😁👍

10/03/2023

Very proud of my boy, Sam Pixley’s work on his Seat Leon BTCC edition. He found it on Copart(hard to find 1.2 turbo model), bought it in, & diagnosed that the engine was in need of a rebuild. He stripped the engine down, identified what was faulty or damaged, & sourced the needed rebuild parts to do the job. Just put it back in and it runs very nicely & pulls well with no leaks😁 The kid’s got good hands!💯 Great job, love ya buddy!

12/02/2023

Thought I’d knock out an “easy” job on my Saturday in the shop, ended up getting my PhD in police car spot light maintenance & repair!😁🤣 Spot light comes off of a true to the film Bluesmobile cop car replica😁 Had seized swivel head due to the old grease going solid like wax. Freed off, lubed, cleaned thoroughly, and packed in CV grease for the win. Finally got a circuit for the power feed thru the two sliding copper joints, which was the time consuming part. Ended up being a small dome of solder on each of the contacts to tighten up the connections did the trick. Once the new spot light bulb arrives, it’ll work as it should. Jobs a good ‘un👍😁

12/02/2023

Happy 2nd Birthday to Dexter! He’s a good boy!😁💯