Trumpf Powertool

Startseite
Schweiz
Grüsch
Trumpf Powertool

TRUMPF electric and battery-powered tools were especially developed for tasks in different areas.

23/06/2026

What wins: years of habit or the right tool? 👀

Andy and Silke set out to answer that question by putting the TKA 700 head-to-head against an angle grinder.

Spoiler: the difference becomes obvious pretty quickly.

While the angle grinder depends heavily on the operator, the TKA 700 delivers exactly what beveling is all about:
consistent results, defined bevels and full control over the final outcome.

And then things get creative.

Because the TKA 700 does more than adjust bevel lengths and bevel angles. With the radius cutter, it can create shapes you would not normally expect to see during weld preparation. 🌸

In the end, there is a perfect edge, a flower made of metal and one clear takeaway:

Some tools get the job done.
Others make the result repeatable. 😎

👉 Try it out for yourself and send us an email for a live demonstration!
✉ [email protected]

TruTool TKA 700

19/06/2026

Sometimes, it’s just a matter of a few millimeters. 😄

For example, between a metal pipe and a wall.

That’s exactly where our colleagues from Finland show why the S 114 is in a league of its own.

Where many tools run out of space or require a workaround, this compact shear cuts the pipe right up to the wall.

No guessing how to remove the last few millimeters.
No “we’ll finish that part later.”

Just make the cut and move on.

What makes the S 114 stand out:
⚙️ Cuts pipes, profiles and sheet metal up to 1.6 mm
⚙️ Extremely compact design for hard-to-reach areas
⚙️ Cordless 12V technology for maximum freedom of movement
⚙️ Clean cuts without sparks and without thermal impact on the material

👉 Try it out yourself and send us an e-mail for a live demonstration!

TruTool S 114

✉ [email protected]

16/06/2026

The Football Game is in full swing and everything should really be about passes, goals and tactics ⚽🏆

But our Sales Partners have found their own discipline: sack racing. 😄

While the big stages are all about competing for points, this here reveals a different truth:
The “big guys” suddenly become quite small again.

No extra time, just timing, balance and a lot of ambition inside a sack. 😅

And just like in the Football Game, the same rule applies here:
A perfect start can decide everything.

Between laughter, stumbling and surprisingly athletic performances, one thing becomes clear:
Team spirit works without a ball as well, just a bit more bouncy.

The Games provide the stage.
Our Sales Partners provide the side events. 🐰⚽

👉 If you have any questions about our machines or would like have a live demonstration, email our experts directly at: ✉ [email protected]

09/06/2026

“Today we’re taking a look inside the TSC 100.” 🔧

Sounds simple enough.
Until someone suggests cutting open a perfectly good TPC 165 to do it. 😅

Luckily, Luca stepped in just in time and reminded everyone that we already have a cutaway model for exactly this purpose.

And that’s where things get interesting:
No magic. No hidden tricks.
Just a precisely engineered interaction of the drive system, eccentric shafts, rocker arms and many other mechanical components.

The result?
The TSC 100 removes slag reliably, accurately and exactly where it needs to be removed.

What we especially like:
While others talk about durability, our engineer was personally involved in developing the machine and sums it up perfectly:

“It works, works and works.” 😎

Sometimes the best technology is the kind you simply switch on and trust to do its job, day after day.

👉 Try it out by yourself and send us an e-mail for a live demonstration.
✉ [email protected]

TruTool TSC 100 - "Andy ist TRUMPF"

05/06/2026

The first time using the TKF 1500… and suddenly beveling a pipe feels a lot more relaxed 😄

Our customer is preparing a large pipe for welding.
In the past, this kind of job often meant grinding, sparks flying and plenty of dust and fumes from cutting.

This time it looks different:
Still manual work, but faster, more controlled and significantly cleaner.

The TKF 1500 guides the tool steadily along the edge and produces a consistent bevel for proper weld seam preparation.

What you can clearly see in the video:
⚙️ Consistent bevel quality over long sections
⚙️ Much lower exposure to sparks, dust and fumes compared to grinding
⚙️ Clean and repeatable results
⚙️ Ergonomic manual guidance for large pipe diameters

And the moment says it all:
A short pause, a look at the result… and that quiet “this is easier than expected” reaction 😄

Manual work stays manual work.
Just the kind you don’t mind doing.

👉 Our experts also do live demonstrations on site. If you are interested, send us an e-mail and try it out by yourself!

TruTool TKF 1500

✉ [email protected]

02/06/2026

They are not allowed to see what is in front of them. Yet they still think they know it. 👀😄

Laurin and Leano take on a very special challenge:
Identifying a TRUMPF Power Tool machine only by touch.

No hints.
No cheating.
Just fingertip feel and a lot of confidence.

With their slightly unusual eye masks, things do not get any easier 😅

Will they recognize the correct TRUMPF Power Tool machine or are they completely off?

Watch until the end and let us know in the comments if you would have figured it out faster. 👇

👉 Touch, test, and be convinced! Request a live demo now and experience the power of TRUMPF firsthand! Send us an e-mail ✉ [email protected]

TruTool C 250 with chip clipper

29/05/2026

The Football World Cup is getting closer and our Global Sales Partners have already started training ⚽😄

The rules are simple:
One goal.
One target.
And suddenly, things get way more serious than expected.

The first shot? Full confidence.
The second? A lot more adrenaline.
And by the third one, someone is already asking if the goal has always been this small 😅

Pressure is rising.
Focus too.
And somewhere, the first self-proclaimed world-class coach has already appeared.

The big question remains:
Who will get every ball into the goal? 👀

Are you already ready for the Football World Cup? ⚽🔥

👉 If you have any questions about our machines or would like have a live demonstration, email our experts directly at: ✉ [email protected]

26/05/2026

From the outside, the N 700 already looks powerful.
From the inside, it gets really interesting 🔧
In the video, Andy opens up the nibbler as a cutaway model, revealing the inner workings and suddenly it becomes clear why 7 mm steel is no challenge for this machine.
Inside, a perfectly tuned interaction of drive system, power transmission and mechanics works together to deliver punching force exactly where it is needed.
Planetary gears, eccentric shafts and many other components work together like a well-rehearsed team.
Sounds technical? It is.
And that is exactly what makes it so fascinating to watch ⚙️
The result:
• High punching force for material up to 7 mm
• Controlled and consistent cutting performance
• Power delivered exactly where it is needed
• Built for heavy-duty applications
Or simply put:
Outside a tool.
Inside engineering excellence.
👉 Our experts also do live demonstrations on site. If you are interested, send us an e-mail and try it out by yourself!
TruTool N 700 - "Andy ist TRUMPF"
https://www.trumpf.com/en_INT/products/power-tools/nibbler/trutool-n-700/
✉ [email protected]

26/05/2026

From the outside, the N 700 already looks powerful.
From the inside, it gets really interesting 🔧

In the video, Andy opens up the nibbler as a cutaway model, revealing the inner workings and suddenly it becomes clear why 7 mm steel is no challenge for this machine.

Inside, a perfectly tuned interaction of drive system, power transmission and mechanics works together to deliver punching force exactly where it is needed.

Planetary gears, eccentric shafts and many other components work together like a well-rehearsed team.

Sounds technical? It is.
And that is exactly what makes it so fascinating to watch ⚙️

The result:
• High punching force for material up to 7 mm
• Controlled and consistent cutting performance
• Power delivered exactly where it is needed
• Built for heavy-duty applications

Or simply put:
Outside a tool.
Inside engineering excellence.

👉 Our experts also do live demonstrations on site. If you are interested, send us an e-mail and try it out by yourself!

TruTool N 700 - "Andy ist TRUMPF"
✉ [email protected]

22/05/2026

We all know the problem 😄
You start cutting a sandwich panel…
and then realize the saw can’t reach through the full depth.
So now it’s time to:
Flip the panel, realign it and make a second cut.
Our colleagues from Italy show how the TPC 165 makes things much easier:
Open it up, position it and cut through the entire panel in one go.
No second round.
No flipping.
No wasted time.
And that’s exactly what the TPC 165 was built for:
⚡ Cuts sandwich panels up to 165 mm thick
⚡ Straight cuts and interior cut-outs possible
⚡ Precise guidance for clean results
⚡ Faster workflow directly on site
While other tools are still deciding which side to cut from, the TPC 165 is already done 😄
👉 Our experts also do live demonstrations on site. If you are interested, send us an e-mail and try it out by yourself!
TruTool TPC 165
https://www.trumpf.com/en_INT/products/power-tools/panel-cutter/
✉ [email protected]

Adresse

TRUMPF Strasse 8
Grüsch
7214

Webseite

https://www.trumpf.com/en_INT/products/power-tools/

Benachrichtigungen

Lassen Sie sich von uns eine E-Mail senden und seien Sie der erste der Neuigkeiten und Aktionen von Trumpf Powertool erfährt. Ihre E-Mail-Adresse wird nicht für andere Zwecke verwendet und Sie können sich jederzeit abmelden.