Container Modification World

Directions Website

Container Modification World Container Modification World manufactures and retails the world's largest selection of Shipping Container Modification Accessories.

09/30/2026

No welding, no painting. Just a grinder, a drill and a rivet gun.

Our 36” man door kit includes the header and footer flanges, side frames, rain drip, rivets, bulb seal and hardware.

🔗 Shop the kit through the link in our bio.

09/17/2026

Our bolt-on Wood Truss Brackets require no welding and no holes through the container roof.

Available in kits for 10 ft, 20 ft and 40 ft containers.

This container bar needed a wood canopy over the large roll-up openings. The brackets gave the crew consistent mounting ...
09/15/2026

This container bar needed a wood canopy over the large roll-up openings. The brackets gave the crew consistent mounting points along the top of the container and helped keep the roof framing lined up from end to end.

It’s a simple system that saves a lot of measuring, fabricating and welding on site.

Link in the bio!

Putting a wood roof on a shipping container?We designed these truss brackets to make the job a whole lot easier. They gi...
09/14/2026

Putting a wood roof on a shipping container?

We designed these truss brackets to make the job a whole lot easier. They give every truss a consistent place to sit without welding or putting holes through the inside of the container.

Kits are available for 10ft, 20ft and 40ft containers with the hardware included.

No more swinging a cargo door open every time you need one tool. Walk in, walk out.Our frames are formed to sit in the c...
09/03/2026

No more swinging a cargo door open every time you need one tool. Walk in, walk out.

Our frames are formed to sit in the container's corrugation, so the kit rivets and screws straight on. No welder, no cutting jig, no paint touch-up, no rust worry down the road.

Link down below!

Swipe →MSS™ strut brackets, wood truss brackets, a BIG AIR® T16 vent and our Dual Sw***er man door. Bolt-on, no welding,...
09/01/2026

Swipe →

MSS™ strut brackets, wood truss brackets, a BIG AIR® T16 vent and our Dual Sw***er man door.

Bolt-on, no welding, all in stock. Link in bio.

Welded HSS frame: stronger, pricier, needs a welder, needs paint, eventually rusts.This: laser-cut galvanized, follows t...
08/31/2026

Welded HSS frame: stronger, pricier, needs a welder, needs paint, eventually rusts.

This: laser-cut galvanized, follows the corrugation, drains by design, fastens on with a drill and a rivet gun. No welder. No paint. No rust.

Link in bio.

Anyone who's mounted strut in a container knows the routine. Weld it in, burn the paint off the outside, grind it flat, ...
08/27/2026

Anyone who's mounted strut in a container knows the routine. Weld it in, burn the paint off the outside, grind it flat, touch it up. Then do it again three feet over.

These bolt straight to the corrugation. No welder, no touch-up, no holes through the wall.

08/19/2026

Everyone in the shop was just holding their breath until this thing actually touched the concrete.

Glad the rigging crew knows what they’re doing because watching that much weight swing around is wild.

Our solar mounting kit screws to the container's top tubing and bottom channel never through the envelope. Adjustable ti...
08/12/2026

Our solar mounting kit screws to the container's top tubing and bottom channel never through the envelope.

Adjustable tilt lets you flatten it for wind season or steepen it for low winter sun, and it fits the common panel sizes: 60, 72, 98, 120, and 144 cell.

Link in the bio!

Address

507 Cory Crescent
Saskatoon, SK
S7K3J7

Website

, ,

Alerts

Be the first to know and let us send you an email when Container Modification World posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category