Machine Tool Solutions Ltd.

Directions Website Contact the business

Machine Tool Solutions Ltd. Machine Tool Solutions Ltd. was established in 1989. Our mission at MTS, is to provide "intelligent

A day on the floor at the Salon Industriel de Québec.Machines, suppliers and shop people all in one building.Spotted LAN...
10/08/2026

A day on the floor at the Salon Industriel de Québec.

Machines, suppliers and shop people all in one building.

Spotted LANG workholding on the table at the Aldo Équipements booth. Always good to see.

Thanks to Magazine MCI for hosting.

Seeing it at a show is easy. Making it work in your shop is the real job.AMB and IMTS proved it again: manufacturing and...
09/30/2026

Seeing it at a show is easy. Making it work in your shop is the real job.

AMB and IMTS proved it again: manufacturing and innovation run parallel. The tech is impressive, but results come from matching it to your parts, your machines, and your process.

Got a setup worth improving? DM us or reach out to MTS.

A wall of vises, stored and ready for a robot to pick.That's RoboTrex Compact, seen at AMB Stuttgart last week.Simple to...
09/24/2026

A wall of vises, stored and ready for a robot to pick.

That's RoboTrex Compact, seen at AMB Stuttgart last week.
Simple to run. Small footprint. Built to keep spindles cutting.

Follow us for the latest workholding innovations from Europe.
Machine Tool Solutions Ltd. Bringing European workholding to Canadian shops.

Machinist MachineShop

IMTS was amazing!Machined American flags on Lang Technik vise jawsPatent pending clamping from FastMill holding real aer...
09/16/2026

IMTS was amazing!

Machined American flags on Lang Technik vise jaws
Patent pending clamping from FastMill holding real aerospace parts
A show floor that did not slow down for two straight days

Next stop: EMO, Germany 🇩🇪

This is the level of detail that keeps us proud to carry these lines. Got questions about what you saw here? Send us a message.

Twenty years of buildup meets a wire wheel and a steady hand 🔧This magnetic lifter came in dead. Corroded board, seized ...
09/03/2026

Twenty years of buildup meets a wire wheel and a steady hand 🔧

This magnetic lifter came in dead. Corroded board, seized internals, wiring that needed a full redo. Few days later, back in service.

Repair work isn’t glamorous but it’s some of the most satisfying stuff we do in the shop.

Got a lifter or workholding piece that needs a second life? Send us a message.

Pull it.Check it.Put it back.Same zero. Every time.Permanent reference points mean inspection doesn't cost you your setu...
08/14/2026

Pull it.
Check it.
Put it back.

Same zero. Every time.

Permanent reference points mean inspection doesn't cost you your setup.

One partner. Every stage of the job. 👊Workholding, automation, turning, material handling, and the service to back it up...
08/07/2026

One partner. Every stage of the job. 👊

Workholding, automation, turning, material handling, and the service to back it up. All in stock in Canada. No overseas wait times.

Zero point systems aren't about the clamp.They're about what happens before the part gets there.Preset the next job on a...
07/17/2026

Zero point systems aren't about the clamp.
They're about what happens before the part gets there.

Preset the next job on a spare plate
While the spindle is still cutting
Drop it in when the current part is done
Already located. No touch off.
The setup happens somewhere else.
The machine never waits on you.

Same spot every time isn't the same as the right spot.Accurate = close to target.Repeatable = consistent, on target or n...
07/10/2026

Same spot every time isn't the same as the right spot.
Accurate = close to target.
Repeatable = consistent, on target or not.
A process can hit the same spot and still be wrong. Or average out correct while never repeating the same way twice.
In production, repeatable usually wins.

Quick one for the shop floor: if your machine hits the same spot every time but it's not the right spot, is that accurat...
07/08/2026

Quick one for the shop floor: if your machine hits the same spot every time but it's not the right spot, is that accurate?

Nope. That's repeatable, not accurate. Two different things, and the difference actually matters.

Repeatable and wrong is fixable, you just dial in the offset.
Accurate but inconsistent is the harder problem, because you never know which way it'll be off next.

Address

8 Automatic Road C#6
Brampton, ON
L6S5N3

Opening Hours

Monday 8:30am - 4:30pm
Tuesday 8:30am - 4:30pm
Wednesday 8:30am - 4:30pm
Thursday 8:30am - 4:30pm
Friday 8:30am - 4:30pm

Website

Alerts

Be the first to know and let us send you an email when Machine Tool Solutions Ltd. posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Machine Tool Solutions Ltd.:

Shortcuts

Share