SPH

SPH Contact information, map and directions, contact form, opening hours, services, ratings, photos, videos and announcements from SPH, Engineering service, 68 Mustang Drive, Rutherford.

SPH Hydraulics is a hydraulic equipment repair specialist based out of Rutherford NSW - servicing the NSW Hunter Valley area
Our fully equipped workshop in Rutherford will have you covered with our full service, repair & testing facilities

CAT 793 Rear strut overhauled for another great customer.We will be sending two 793 Rear struts up to QLD tomorrow.For a...
28/05/2026

CAT 793 Rear strut overhauled for another great customer.

We will be sending two 793 Rear struts up to QLD tomorrow.

For all your hydraulic cylinder needs. Contact us on 4932 0113 or email [email protected]

D11 Blade Lifts for one of our customers up in the Valley.This customer wanted to give their dozer a little overhaul wit...
26/05/2026

D11 Blade Lifts for one of our customers up in the Valley.

This customer wanted to give their dozer a little overhaul without going over the top.

Reseal with genuine CAT seals.
New CAT bearings.
Hone to spec to deglaze.
Linish the rod.
One rod got an eye reclaim which was all done in house.

If you’re looking for a reputable hydraulic rebuild shop for your hydraulic cylinders. Give us a call on 4932 0113

Hitachi Stick cylinder,Came in with a damaged rod and customer was happy to replace.Out sourced the rod to our good frie...
12/05/2026

Hitachi Stick cylinder,

Came in with a damaged rod and customer was happy to replace.

Out sourced the rod to our good friend at Stanson Precision Engineeering and came back to us to weld the eye & reassemble.

If you need any repairs similar come in or give the team a call on 4932 0113

68 Mustang Drive Rutherford

25/04/2026

🤟🏼 Anytime man, goodluck racing!

The past week we had a few machines roll in for repairs.John Deere tractor. X2 lift cylinder overhaul and the steering c...
25/04/2026

The past week we had a few machines roll in for repairs.

John Deere tractor. X2 lift cylinder overhaul and the steering cylinder got a reseal.

And a little dingo came in for battery not charging, Stator wires were damaged.
Also had a leaking flow control valve.

We are located in 68 Mustang Drive Rutherford.

If you need your machinery fixed or components repaired come drop them by.

4932 0113

Hope everyone had a great Easter break!Here is a 740 Strut off a Volvo haul truck ready for another great customer.This ...
09/04/2026

Hope everyone had a great Easter break!

Here is a 740 Strut off a Volvo haul truck ready for another great customer.

This strut got a full overhaul.

Reseal
Rechrome
Hone the barrel
New bearings
New charge valves
Paint

If you need any mechanical work, we do it all here at SPH. Bring in your machinery and we will get you back to site without any dramas.

68 mustang drive Rutherford

4932 0113

One of the jobs the team tackled this week.Customer called to see if we could do a rush job, they were meant to drop the...
02/04/2026

One of the jobs the team tackled this week.

Customer called to see if we could do a rush job, they were meant to drop the cylinder only off to us on Monday. They couldn’t get the pin out so they asked can we give it a go.

Of course we can. Using our 100T hollow ram, we were able to pull the pin out, reseal the cylinder and all back together.

This time making the pin grease-able.

Hopefully everyone has a great Easter long weekend! Safe travels.

We are looking to branch out our customer base!If you are needing work on your equipment done.We offer a large range of ...
18/03/2026

We are looking to branch out our customer base!

If you are needing work on your equipment done.

We offer a large range of services.

Repair Hydraulic components.
Machinery repairs to small equipment & large.
Machining.
Boilermaking & Fabrication repairs.
Test & tagging.

All done on site in Rutherford NSW
4932 0113

Yesterday afternoon we had a 980M loader that came in for x2 hoist cylinder reseals.Customer wanted the rod assembly’s o...
28/02/2026

Yesterday afternoon we had a 980M loader that came in for x2 hoist cylinder reseals.

Customer wanted the rod assembly’s out and keep the barrels in, unless there was any damage.

Barrels were within spec but the issue was the rod seals have failed due to their age.

The loader is ready to go back to work first thing Monday morning.

If you didn’t know, we can also work on your machinery at our workshop if you cannot get the job done on site.

Here at SPH hydraulics we are experienced in components and machinery repairs.

Give the team a call on 4932 0113
68 mustang drive Rutherford, 2320

We have been abit slow on the socials with posting to start the year off.Cannot thank our great clients enough of last y...
12/02/2026

We have been abit slow on the socials with posting to start the year off.

Cannot thank our great clients enough of last year. We cant wait to keep working together through out this year.

The start of this year we have hit the ground running and we are more prepared than ever.

Come see the team at SPH hydraulics & engineering in at 68 mustang drive Rutherford for any hydraulic cylinder work.

Address

68 Mustang Drive
Rutherford, NSW
2320

Opening Hours

Monday 7am - 4pm
Tuesday 7am - 4pm
Wednesday 7am - 4pm
Thursday 7am - 4pm
Friday 7am - 4pm

Telephone

+61249320113

Website

Alerts

Be the first to know and let us send you an email when SPH posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to SPH:

Shortcuts

Share

Category