Handy Machining

Handy Machining General Machining Lathe Milling Machine 30 ton press , prototyping, repairs, small parts runs

Job done and finished for 600 engineering at 600 engineering today Design and build a partition in this tipper to enable...
12/03/2026

Job done and finished for 600 engineering at 600 engineering today
Design and build a partition in this tipper to enable dropping 2 loads of 2 cubic metres of firewood at two different locations
600’s client will be putting it to work tomorrow delivering firewood in the Yarra Valley

Reclaiming a couple of axles for a skid steer that had torn the keyways out It’s an older machine so hard to find new or...
08/03/2026

Reclaiming a couple of axles for a skid steer that had torn the keyways out
It’s an older machine so hard to find new or good axles
Welded up all the damaged sections and a bit more then machine back to correct diameters for both the sprocket and the bearing journal’s then cut in the two new keyways at 135 degrees separation
These jobs are always more time consuming than clients can appreciate but that’s all just part and parcel of the dark magic of getting it done

Just finished helping out a mate and former work colleague with some sn**ch block storage solutions on his new lorry In ...
28/02/2026

Just finished helping out a mate and former work colleague with some sn**ch block storage solutions on his new lorry
In some ways I miss driving these things in other ways not
Very nice truck Ben all the best with it

An old school bloke using old school methods to cut in a hole into a 25mm road plate prior to welding in a lifting inser...
21/01/2026

An old school bloke using old school methods to cut in a hole into a 25mm road plate prior to welding in a lifting insert
64 years old and still got trainer wheels on the gas axe 😂😂

A bit of time spent mostly on the mill today at 600 A bus suspension part with badly stripped out threads required repai...
12/01/2026

A bit of time spent mostly on the mill today at 600
A bus suspension part with badly stripped out threads required repair
Drilled out the damaged 18 mm thread remains and tapped a 22mm thread 50mm deep
Then make new thread inserts to suit and install them now it’s back to OEM spec and ready to go back into service

21/11/2025

Haven’t seen one of these for a long time
Triple Webber manifold for a Holden six
A quick skim to bring it back to flat Half an hour to set it up and another half hour to tram the mill head back true again but jobs done

Now this is proof that I never know what the next job is going to be Machine up a mounting bezel for a camera lens that ...
26/09/2025

Now this is proof that I never know what the next job is going to be
Machine up a mounting bezel for a camera lens that was made in 1870 😳
You know the old school camera that had a big box on a tripod and the photographer had the black cloth over them and camera to take a photo
The tread is 4 inch x 24 TPI as luck had it I had a piece of bronze around the correct size that I’d salvaged from an excavator bushing sitting in my scrap pile. Well now it’s reborn into something useful again

Bloody turbo Saab exhaust manifold as a mechanic I was glad to see the end of them now doing what I do one has popped up...
06/09/2025

Bloody turbo Saab exhaust manifold as a mechanic I was glad to see the end of them now doing what I do one has popped up to haunt me
Crazy design means crazy method needed to clamp it down for machining

Drive pulley for a client fitting a supercharger to an engine I hope these guys have done their maths correctly big jump...
01/09/2025

Drive pulley for a client fitting a supercharger to an engine
I hope these guys have done their maths correctly big jump from 173mm to 220mm

New parts for an old unit.Axle and brake control rod for a 1931 Chev How differently they did things in the past the axl...
24/08/2025

New parts for an old unit.Axle and brake control rod for a 1931 Chev
How differently they did things in the past the axle has course splines and a taper & keyed end to fit into a tapered wheel hub
It required several different set up’s on both lathe and mill to machine it but I think much more durable than the original that had broken and been welded at some point in the past
And a brake control rod for mechanical brake set up 😳 I think it might have required a pretty strong right leg or two feet to pull one of these old girls up in a hurry

06/08/2025

Job done at 600 engineering today
Machine this piece of steel to size and then put a 20 degree bevel on it
It is 750 long 130 wide and 45 thick
The tricky part was holding it secure in the mill table so fabricated a rigid frame and temporary welded it to the bottom surface
And the bolted the frame to the table

Address

6 Clancy’s Road Mt Evelyn
Melbourne, VIC
3796

Opening Hours

Monday 8am - 8pm
Tuesday 8am - 8pm
Wednesday 8am - 8pm
Thursday 8am - 8pm
Friday 8am - 8pm
Saturday 9am - 5pm
Sunday 9am - 5pm

Telephone

0428371001

Website

Alerts

Be the first to know and let us send you an email when Handy Machining posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Handy Machining:

Shortcuts

Share