Performance Race Services

Performance Race Services Contact information, map and directions, contact form, opening hours, services, ratings, photos, videos and announcements from Performance Race Services, Metal Fabricator, 3/27 sweny Drive, Australind.

Western Australia's high end custom fabrication and developments for all motorsport and general fabrication,
roll cages
turbo manifolds
exhausts
intercooler and intake plumbing design and setup
plumbing solutions
exotic materials
engine enhancement

29/05/2026

Some very cool project pieces happening, this is one of them!
You can think of it we'll find a way to make it work!

PH: 0429545598
ADD: unit 3/27 Sweny Dr Australind
Email: [email protected]

Hey guys, more frustrating and annoying going on. Theyre is apparently an instagram account also taking deposits and pay...
28/05/2026

Hey guys, more frustrating and annoying going on. Theyre is apparently an instagram account also taking deposits and payments to from clients and using our business a front. Please report this also. I've had enough of my reputation being put on the line.

Thanks
Jaxon!

Old school cool. Corvette with a lovely new set of headers and 2.5" exhaust to suit. All new hangers and mounts to go.Bi...
19/05/2026

Old school cool.
Corvette with a lovely new set of headers and 2.5" exhaust to suit.
All new hangers and mounts to go.

Bit of an upgrade from the old setup

PH: 0429545598
ADD: unit 3/27 Sweny Dr Australind
Email: [email protected]

19/05/2026

For the exhaust diy goers
Lost wax cast ej20/25 bellmouth.
Save the hassle of making 2 piece rube style with a fl**ge and save the hours!

All subaru downpipes fabricated here will now run one of these as a standard item.

We will also stock them or have available to order if required.

Let's call this part 1.we've been tending to getting this car back to health for the last long few months.the mighty red...
06/05/2026

Let's call this part 1.

we've been tending to getting this car back to health for the last long few months.

the mighty red rocket of a subaru came in with a cracked cylinder head at the rocker cover after failure on the track. No big deal remove and weld up. fix the issue.

shortly after the engine is out and here we are.
bent valve, cracked valve guides, damaged piston, corroded bores with pitting. this is the start of it all.
when pulling the heads off we discovered that the exhaust ports were over ported and had blown through into the head stud provision on both heads, slowly erroding away the studs.

further investigation with splitting the block found failure thrust area on bearings and more bore damage.

Was only a matter of time before total disaster more than what it was already.

anyway that's part 1

What a man wants, he gets! A bit (or a lot) of patience and persistence is all you need to make it happen. I somehow man...
04/05/2026

What a man wants, he gets!

A bit (or a lot) of patience and persistence is all you need to make it happen.

I somehow managed to fit a dual 3.5" exhaust setup up and over the diff into a 200 series.

No space left under there to breathe!
We have some new downpipes going in in a couple weeks before it hits the dyno!

PH: 0429545598
ADD: unit 3/27 Sweny Dr Australind
Email: [email protected]

01/05/2026

A pleasant view on this lovely freehand friday..

Holy banana bend batman.. Rb30 turbo manifold leaking on both ends. Removed and inspected to find a 4mm bow from centre ...
19/04/2026

Holy banana bend batman..

Rb30 turbo manifold leaking on both ends. Removed and inspected to find a 4mm bow from centre to end both ways.

Firstly Pressed straight and then centre of fl**ge cut out to allow access for crack repair and welding/peening for preventative. Then aligned on mill and machined flat. Multiple passes as it was also twisted 20thou. Now nice and straight ready to go back on.

Unfortunately the curve this manifold had after removing is mostly from poor fabrication technique and welding process allowing it to curve like it did.

For all your fabrication and welding requirements, get in touch today!
PH: 0429545598
ADD: unit 3/27 Sweny Dr Australind
Email: [email protected]

Finally have these kits ready for fabrication and ordering to suit your specific application.Vq35de Centre coolant kit. ...
13/04/2026

Finally have these kits ready for fabrication and ordering to suit your specific application.

Vq35de Centre coolant kit. With some variations. This bad boys heading overseas. Pretty cool little achievement for us!

Thanks to all!

For all your fabrication and welding requirements, get in touch today!
PH: 0429545598
ADD: unit 3/27 Sweny Dr Australind
Email: [email protected]

This one was a real challenge, just how I like it! Tasked with remaking a new turbo manifold for the Audi quattro motor ...
20/12/2025

This one was a real challenge, just how I like it! Tasked with remaking a new turbo manifold for the Audi quattro motor to replace the cracked original. Space constraints galore. I think I succeeded in making it possible!

For all your fabrication and welding requirements, get in touch today!
PH: 0429545598
ADD: unit 3/27 Sweny Dr Australind

Address

3/27 Sweny Drive
Australind, WA
6233

Opening Hours

Monday 9am - 5pm
Tuesday 8am - 6pm
Wednesday 8am - 6pm
Thursday 8am - 6pm
Friday 8am - 6pm

Telephone

+61429545598

Website

Alerts

Be the first to know and let us send you an email when Performance Race Services posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Performance Race Services:

Shortcuts

Share

Category