Ultra-Shear Router Bits & Saw Blades

Call Website Contact the business

Ultra-Shear Router Bits & Saw Blades We offer hundreds of precision-ground carbide bits and blades built for clean, accurate cuts.

10/24/2026

Looking for the right engraving bit? We make 18 different profiles — angles from 15° to 90°, pencil tips and flat tips, 2-flute and 3-flute designs — all solid carbide, all made in Ohio.

If you're engraving dense hardwoods or plastics on a CNC, the 3-flute bits (40°, 50°, 60°, and 90°) let you increase feed rate by 50% while holding the same finish quality as standard 2-flute bits. The shear angle cuts cleanly through tropical hardwoods and plastics without chipout.

All bits work equally well in a CNC, with template guides, or freehand. Available individually, in 4-packs, a 9-piece set, or the full 18-piece master set.

Scroll through to see every profile, or visit our page to find the angle and tip combination you need.

https://woodpeck.com/products/ultra-shear-engraving-router-bits-solid-carbide?utm_source=facebook&utm_medium=organic_social&utm_campaign=engravingbits-10-26

10/24/2026

Small router doesn't mean small projects. These 1/2" diameter carbide-tipped pattern bits are built for compact routers with 1/4" shanks — tight enough for control, capable enough for pattern routing chair legs, coasters, and complex duplicates. Three cut lengths — 1/2", 3/4", and 1" — to match your stock thickness. The bearing follows the pattern, the carbide cuts clean, and you get a surface ready for final sanding. Pattern routing without the big router. Made in Ohio.

https://woodpeck.com/products/ultra-shear-carbide-tipped-1-4-shank-1-2-diameter-2-flute-template-pattern-router-bits?utm_source=facebook&utm_medium=organic_social&utm_campaign=carbidetippedpatternbits-10-26

10/23/2026

Watch how a flat-top grind changes the way you cut grooves. No score marks, no ridges — just perfectly flat-bottomed cuts ready for glue-up. These 40-tooth blades handle dadoes, box joints, splines, and drawer grooves in solid stock and plywood, even through paper-thin veneers. Available in 1/8", 3/16", and 1/4" kerfs so you can match the joint without stacking or shimming. American-made steel plates, brazed carbide teeth, and optimized grind angles for clean cuts and quiet operation. Learn more.

https://woodpeck.com/products/ultra-shear-flat-top-grooving-saw-blades?utm_source=facebook&utm_medium=organic_social&utm_campaign=flattopgroovingblades-10-26

When you're rabbeting tight curves or inside corners on smaller work — box backs, picture frames, glass retainers — stan...
10/23/2026

When you're rabbeting tight curves or inside corners on smaller work — box backs, picture frames, glass retainers — standard rabbeting bits often can't reach cleanly into the detail. The cutter diameter is too large, leaving rounded-over corners or incomplete rabbets where precision matters.

Ultra-Shear's Mini Rabbeting Set solves that with a 7/8" diameter cutter and four interchangeable bearings that cut rabbets from 1/16" to 1/4" in 1/16" increments. A fifth bearing lets the same bit work as a flush trim bit. The smaller profile gets tighter into curves and corners, keeping your rabbet depth consistent where larger bits physically can't go.

The bit uses a three-flute carbide-tipped design and a 1/4" shank. Changing bearing sizes is straightforward — loosen the machine screw, swap bearings, and you're cutting at the new depth.

Machined in Northeast Ohio with state-of-the-art CNC equipment and high-quality carbide, these bits are sold direct from the manufacturer. If you work on curved or detailed projects where rabbets need to reach into tighter geometry, this set handles what the bigger interchangeable-bearing sets can't.

Learn more about the Ultra-Shear Mini Rabbeting Set.

https://woodpeck.com/products/ultra-shear-carbide-tipped-mini-rabbeting-router-bits?utm_source=facebook&utm_medium=organic_social&utm_campaign=minirabbetingbits-10-26

10/22/2026

Tight radius inlay work or narrow banding where standard pattern bits won't fit? Our Micro-Bearing Pattern Bits put the bearing above a tiny solid carbide head — down to 3/16" diameter — so you can follow intricate curves and reach into details larger cutters leave behind. The unique construction handles pattern routing in narrow pockets and sharp inside corners without trampling adjacent surfaces.

Available in 3/16" and 1/4" diameters, multiple cut lengths, straight or spiral geometry, and machined from solid nano-grain carbide in Ohio. These require careful feed rates and setup, but no other pattern bit gets into this kind of space.

Learn more at woodpeck.com

https://woodpeck.com/products/ultra-shear-micro-bearing-1-4-inch-shank-carbide-head-pattern-router-bits?utm_source=facebook&utm_medium=organic_social&utm_campaign=microbearingpatternbits-10-26

10/21/2026

Ripping 8/4 hardwood? Fewer teeth, not more. The 20-Tooth Thick Stock Rip Blade uses deeply curved gullets to clear massive amounts of shavings out of the kerf — less friction, less burning, cleaner feed through thick, dense stock. The flat-top grind minimizes resistance even when you're feeding aggressively. Available in full kerf or thin kerf. American-made steel plate, carbide-tipped, heat treated and tensioned for table saw rip cuts that don't fight you. Learn more.

https://woodpeck.com/products/ultra-shear-10-inch-20-tooth-thick-stock-rip-saw-blade?utm_source=facebook&utm_medium=organic_social&utm_campaign=thickstockripblade-10-26

10/20/2026

Up-cut or down-cut — the difference is in the geometry, and it matters for your flush trim results.

Ultra-Shear solid carbide flush trim bits are available in both configurations. Up-cut pulls chips toward the router, making it the standard choice for solid wood. Down-cut pushes material away and slices into the surface — ideal when you need a clean top edge on plywood or thin-veneer sheet goods.

Both versions use twin bearing pilots matched to the 1/2" cutter diameter, so the bit tracks your template cleanly from either direction. Two spiral flutes, solid carbide construction, and cut lengths from 1" to 2" for pattern routing and flush trimming work.

Choose the cut length closest to your material thickness, then match the geometry to the stock. American-made, factory-direct from Strongsville, Ohio.

https://woodpeck.com/products/ultra-shear-solid-carbide-1-2-inch-diameter-2-flute-flush-trim-router-bits?utm_source=facebook&utm_medium=organic_social&utm_campaign=flushtrimbits-10-26

10/20/2026

Watch how precision meets performance. Every Ultra-Shear router bit — from roundover and chamfer to compression spirals and pattern work — is machined in Strongsville, Ohio using high-grade carbide and steel. Hundreds of profiles, built to cut clean and finish smooth across hardwood, plywood, and edge detail. Whether you're routing joinery, shaping edges, or surfacing spoilboard, the edge quality starts with how the bit is made. Learn more about the full Ultra-Shear router bit lineup.

https://woodpeck.com/collections/router-bits?utm_source=facebook&utm_medium=organic_social&utm_campaign=routerbitbrandvideo-10-26

10/19/2026

HSS router bits are back — and now they're paired with modern spiral geometry.

The grain structure of high-speed steel takes a sharper edge than carbide. In the '70s, when HSS dominated the router bit market, spiral designs like this weren't widely available. Now you get that superior cutting edge combined with up-cut, down-cut, and compression configurations — the geometry that matters for clean cuts in hardwoods and softwoods.

These bits are ground in Strongsville, Ohio, on CNC equipment built for precision. Available in 1/4" and 1/2" shank, with 1" cut length and 2-flute spiral designs.

Carbide won on tool life, not cut quality. HSS metallurgy has advanced significantly in the last 50 years, and with carbide costs rising, high-speed steel offers a sharper edge at a lower entry point — especially for custom work and home shops where cut quality drives the result.

Learn more

https://woodpeck.com/products/ultra-sheer-high-speed-steel-router-bits?utm_source=facebook&utm_medium=organic_social&utm_campaign=highspeedsteelbits-10-26

10/18/2026

Watch how a deeper, parabolic groove transforms finger grip on cutting boards — straight edges or curves.

Ultra-Shear's Deep Finger Grip Groove Bit cuts deeper than most bits on the market and follows the natural contour of fingers. Depth is bearing-controlled, so you can run this profile on curved workpieces just as easily as square-ended boards.

Two bearing sizes included: 3/8" depth with 11/16" cutting height for a pronounced grip, or 3/16" depth with 9/16" height for a subtler profile. Working dense woods or tricky grain? Start with the larger bearing, then switch to the smaller for a final pass — less router stress, cleaner result.

Carbide-tipped, 2-flute, 1/2" shank. Made in Ohio.

https://woodpeck.com/products/ultra-shear-2-flute-carbide-tipped-deep-finger-grip-groove-router-bits?utm_source=facebook&utm_medium=organic_social&utm_campaign=deepfingergripgroovebits-10-26

Address

13700 Prospect Road
Strongsville, OH
44149

Telephone

+18007520725

Website

Alerts

Be the first to know and let us send you an email when Ultra-Shear Router Bits & Saw Blades posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Ultra-Shear Router Bits & Saw Blades:

Shortcuts

Share

Category