Oracle Fabrication

  • Home
  • Oracle Fabrication

Oracle Fabrication Contact information, map and directions, contact form, opening hours, services, ratings, photos, videos and announcements from Oracle Fabrication, Metal Fabricator, .

22/03/2026

Squarebody about to get a brand new .autowire harness! We've been pushing off the first startup after the exhaust/fuel system to make sure everything is properly installed and triple checked! Truck has been down half a decade, whats another few weeks!!!

2016 Hyundai in for exhaust work! In total there were 5 different places where it was leaking, we decided to just pull t...
20/02/2026

2016 Hyundai in for exhaust work! In total there were 5 different places where it was leaking, we decided to just pull the whole system, cut out the bad joints, and scrap all the clamps! Way bigger project than orignally anticipated but glad we were able to help the customer fix this mess! Due to the length of the project, we were not able to get sound clips after the work was completed, but will be checking in on the vehicle in the next few weeks and can post a before/after!

Finally got the fittings in to finish up the feed side of the fuel system! Brand new -6 feed tubes for carb, gauge to ve...
06/02/2026

Finally got the fittings in to finish up the feed side of the fuel system! Brand new -6 feed tubes for carb, gauge to verify the regulator is pushing the correct pressure, a fresh 40 micron Russell filter, and a slick line made up to keep it simple! Getting closer and closer to firing this thing up!!!

Finally received the fittings to get the main fuel feed ran all the way through the regulator to the carb! Absolutely lo...
06/02/2026

Finally received the fittings to get the main fuel feed ran all the way through the regulator to the carb! Absolutely love how slick this setup is looking especially being able to have the regulator readily available but still tucked out of eyesight!

Got the main bulk of the fuel system done and ran! -6 lines and fittings all throughout from the inline filters to the f...
23/01/2026

Got the main bulk of the fuel system done and ran! -6 lines and fittings all throughout from the inline filters to the fuel pump! Waiting to toss the cab back on the mount the regulator and route the return lines! One step closer to getting this thing running!

22/01/2026

Fuel system getting plumbed currently and hopefully we can have this thing cranking over in the next week or two!

21/01/2026

Exhaust is on pause while we wait for some parts to finish the rear but onto the fuel system! Have a Blue electric fuel pump sending fuel to an SS Series fuel regulator to feed this massive 540 Big Block!

16/01/2026

We both think a simple 45 degree downturn is the way to go to keep the system hidden and keep the clean crisp look, especially that the bed skirts dont drop as far as we initially thought!

09/01/2026

Still have a few days of welding the front section but this is the current predicament. Run it to the corner of the bedside, or dump it down and let it breath?!?

Got the rear mounts cut, processed and tacked in! Couple hours start to finish but it ended up being well worth the time...
07/01/2026

Got the rear mounts cut, processed and tacked in! Couple hours start to finish but it ended up being well worth the time! Looks way better than rubber insulators with straight bar mounts that we orignally had planned, plus it allowed us to raise the exhaust up higher to conceal it for a better finished product when its rolling down the road!!!

Up to this point, we got a majority of the system routed, tacked, and hard mounted up to the rear! Throwing around ideas...
06/01/2026

Up to this point, we got a majority of the system routed, tacked, and hard mounted up to the rear! Throwing around ideas on a bedside dump, or just tossing 45 degree downturns on and letting it rumble! Trying to keep this system as clean and as sleek as we can! Its not everyday you get to handbuild an exhaust for a restoration of this level!!!

Address


18704

Website

Alerts

Be the first to know and let us send you an email when Oracle Fabrication posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

  • Want your business to be the top-listed Equipment Service?

Share