Boltright Global Resources Nig LTD

24/11/2018

We just don't render bolting activities, we also render fl**ge management services, this is part of our equipment on cold cutting activities.

12/10/2018

20" × 14 plidco clamp fully aligned and torque to the required torque value.

05/08/2018

https://youtu.be/FqYK0n9XVS8

Nuclear to sub-sea Hydratight leads with innovative and dependable tensioning systems for hydraulic bolt tensioning Find more at http://www.hydratight.com/en...

04/08/2018

Part 2 of fl**ge management(Torque$ Tensioning) Training.

03/08/2018

Fl**ge management training ongoing @ boltright global resources nig Ltd base

03/08/2018

https://youtu.be/jOk6ZYggc4g

This Video depicts the proper use of a hydraulic torque wrench. Visit www.windtechtv.org for more video. Produced by Highland Community College. WindTechTV.o...

16/07/2018

Personel on site job

09/07/2018

So, here’s a list of 11 expert guidelines which will help you use and maintain your torque wrench tool flawlessly. Take a look:

Manufacturer’s directions regarding proper force, torque direction, pattern, lubrication on fasteners and tightening or releasing cycles etc., should be followed without fail every time the torque wrench tool is used.

The tool should never be used to break loose fasteners.

The wrench should never be set at values higher or lower than those indicated on the scale.

Use the wrench with great care. If it is dropped, it will lose its calibration.

Do not under any circumstances use a torque wrench whose calibration certification has expired or is missing.

Always store the wrench in its own storage case after cleaning and setting it at its lowest torque setting, when not in use.

A cheater bar or any other type of extension should never be used to apply extra torque. Instead, use a larger torque wrench.

If the rated torque of the tool is exceeded, it will cause over-torquing which eventually results in wrench or part failure.

Check your tool’s calibration at regular intervals. Especially if the tool falls, is damaged or the environment conditions in which it is stored are altered; it is important to verify the tool’s calibration before using it.

Do not disassemble or try to repair a torque wrench by yourself. The tool should be repaired and calibrated strictly as per the manufacturer’s instructions.

08/07/2018

In Boltright Global Resources Nig. Ltd, we strongly believe there is always a better way to save our customers crucial time and money and have patented several ground-breaking products to do so.

Our Torque and Bolting services is a subsidiary of Boltright Global Resources Nig. Ltd which offers globally-available, first-class, on-site hydraulic bolt tightening services from a simple bolt-up of a single fl**ge connection or ni**le up/down to maintenance and major-shutdown site services. We utilize only the best equipment and tools to deploy a "First-Time, Right-Time" service in the industry.

Our Torque Tools cover a full range of sizes from 1/2" to 5" studs and 7/8" to 7-5/8" a/f nuts, Hi-Force and Enerpac Hydraulic Pumps, Hydraulic and pneumatic wrenches, Hi-fi Force and Enerpac Hydraulic Nut Splitters, Hi -Force and Enerpac Hydraulic Fl**ge Spreaders.

Torque capacity is from 20 lb/ft (34 N/m) to 10,000 lb/ft (80,524 N/m) with manual and hydraulic equipment. We offer Hydraulic Torque Tools with both air and electricity-driven power packs which can be used within hazardous environments such as off-shore platforms, eliminating the need to shut down.

All Boltright Torque Tools are tested and supplied with applicable test or calibration certificates.

18/06/2018

Considering the high level of leaks on our hydrocarbons lines, we in Boltright Global Resources Nig Ltd made a commitment to follow all Torquing and Tensioning procedures to ensure that all Bolts and Nuts are properly Torque and Tension.

OCHI VINNING
Sales/Project Manager

15/06/2018

Inspection on going @ Boltright Global Resources Base